The floor will bulge after a few days of water, and the wooden floor will be swollen, and now it is

After the floor is flooded, there will be different degrees of bulging in about five days. And this has a certain relationship with the material of the floor itself, the indoor temperature, and the degree of dryness and wetness. Generally speaking, wooden floors bulge earlier.

The high indoor temperature also has an early bulging time. Indoor drying will also speed up the rate at which the floor bulges.

1. Sports wood floor bulge.

1. The reason for the bulging of the sports wooden floor.

After the sports wood floor is laid, it swells due to moisture and bulges. This is mostly related to the environment around the sports wood floor, especially the foundation is too wet or the floor is flooded.

2. How to prevent it.

To make the sports wood floor not bulge, pay attention to three points:

1) At the end of the civil works, the sports wood floor cannot be laid immediately;

2) Before the sports wood floor is paved, the dehumidification work should be done on the paved floor, and the moisture content of the sports wood floor should not be less than 8% when laying the wood floor.

3) In the daily maintenance process of sports wood flooring, it is necessary to prevent indoor water leakage in the stadium, and the sports wood floor should not be soaked in water.

Second, the sports wood floor is warped.

1. The reason for the warping of the sports wood floor.

The warping of sports wood flooring is mainly caused by the fact that sports wood flooring has not undergone formal drying treatment.

2. How to prevent it.

1) Before the sports wood floor is paved, the sports wood floor can be placed in the room to be laid two or three days in advance, so that the wood can adapt to the indoor temperature and can also prevent warping.

2) When installing sports wood flooring, a layer of plastic film can be laid under the floor to prevent moisture and prevent the floor from warping;

Generally, because the material expands after absorbing water, it will bulge, and once the floor is bulged, it will be wasted and can only be replaced!

As far as I know, the water bulging of the wood floor needs to see whether the floor is laminate or solid wood flooring. The surface water on the floor should be sucked dry in the shortest possible time, if it is a small area of water, it is recommended not to pry up the laminate floor to dry, which is easy to cause hard damage to the laminate floor, and is likely to cause serious consequences that cannot be restored. It is best to quickly remove the baseboard of the floor, expose the expansion joint, and rely on the expansion joint to dissipate the water vapor, depending on the amount of seepage water, it usually takes about 3 to 10 days to dry.

Solid wood flooring in a small area of water, can be used with a high-power vacuum cleaner to suck out the water vapor, but after the expansion of a large area of water inlet causes damage to the surface paint, the soaked floor should be pried up and dried, with the same kind of paint original, the floor is repainted and waxed.

Laminate flooring can not be blistered for more than 2 hours, if the soaking time is too long, the floor must be pried up and replaced with a new floor, because after a long period of blistering, the laminate floor will be deformed. Even if you can't use it after drying, when the whole skin of the floor is pried open, the water is mopped, and then dried, you can use a fan to accelerate the drying of the ground, if the water can be basically mopped dry by partially priing the floor, then you only need to use an electric fan towards the gap in the floor, and then replace part of the new floor. <

The floor will bulge after a few days of waterIf the soaking time is too long, the floor must be pried up and replaced with a new floor burner, because after the blister during the long staring period, the composite floor will be deformed. Even if you can't use it after drying, laminate flooring can not be blistered for more than 2 hours, when the floor is all pried open, the water is mopped, and then dried, you can use a fan to speed up the drying of the floor. If the water can be largely removed by partially priing the floor, then simply use an electric fan towards the gap in the floor and then replace it with a new floor.

SolutionQuickly remove the baseboard of the floor, expose the expansion joint, and rely on the expansion joint to dissipate the water vapor, depending on the amount of seepage water, it usually takes about 3 to 10 days to dry. When the composite floor encounters water, the first thing is to deal with the stagnant water, the water under the floor is not to care about it for the time being, the most important thing is to keep the ventilation to make it dry naturally, be sure not to use a hair dryer to dry, if it is removed, the floor will be deformed, in order to dry the floor as soon as possible, you can remove the door buckle strip, and the baseboard can also be removed if it is convenient, so that the water can evaporate as soon as possible.