What causes the wood floor to soak in water and bulge? How do you recover?

This situation is caused by the failure of the floor waterproofing. The best thing to do is to remove it and replace it with a new floor.

When the wooden floor encounters water, it will bulge and deform after soaking in water for a long time, and the best way is to find a professional master to repair and replace it.

After the wooden floor is soaked in water, it will bulge that the wooden floor can not be damp, and after being damp, it is easy to bulge and deform.

If the floor is not cleaned before the installation of the floor, resulting in uneven ground or sand, put into use on the floor, after a long time of stepping, the moisture-proof film and the reverse side of the balance layer floor are easily destroyed, so the wet ground will cause the floor to bulge. Many wood floors are swollen due to water ingress in the gaps between the wooden floors, such as heating soaking water or long-term soaking caused by water leakage, etc., which usually belongs to improper use and maintenance, and moisture-proof measures are not done well.

If you do not do a good job of moisture-proof measures when installing the wooden floor, or if you do not treat it well, it will also cause the wooden floor to blister, so when installing the wooden floor, the moisture-proof film connection should be glued with waterproof tape. When the wooden floor is bulging, the arched wooden block can be separated from the surrounding floor, so that after the general time of ventilation, the phenomenon of arching can be alleviated, if the area is relatively large to pry the floor, it should wait for the ground and the keel to be laid before proceeding, laying the floor is to leave a small gap, to give the floor wet expansion and dry space.

If the gap is filled with stains, it will affect the normal expansion of the floor, causing bulging symptoms, so the gap needs to be cleaned up, so that the bulging place will recover. The main reasons for bulging wooden floors are dampness, uneven floors, or sandy floors. Before installation, there was some small sand on the ground or the ground was too rough because the ground was not cleaned.

After the floor is installed, in the process of people stepping on it, the moisture-proof film and the balance layer on the back of the floor are destroyed, and the moisture from the ground enters, causing the floor to bulge. When the floor is laid, the shop is leaning against the wall, there should be a gap of 2 cm as an expansion joint, and then the bottom plate is covered with a stick, some owners in order to clean, the wooden floor store does not require the expansion joint to be reserved between the neighbors, or the layman leaves the gap as fine as possible, which will also make the floor unable to stretch, the humid air is easy to arch after moisture absorption and expansion, and even the paint surface cracks so that the expansion between the wooden floor and the structure appears.

1. On-site inspection.

Sports wood floor maintenance staff, or stadium staff, when they find that the sports wood floor is soaked in water after work, don't panic first, be calm. The first time to inspect the soaking site, eliminate potential safety hazards, such as whether there are wires, electrical appliances, flammable and explosive materials on the soaking floor.

Then according to the degree of water immersion of the sports wood floor, a solution is formulated.

2. Soak in water lightly.

If the sports wood floor is lightly soaked, the lightly soaked and damp floor can be wiped dry and ventilated. If necessary, disassemble the sports wood floor to observe whether there is water on the ground and observe whether the floor is obviously deformed. If so, it needs to be removed and dried, and reinstalled.

3. Heavy soaking.

The sports floor of the body cracked bridge wood floor is seriously damp or soaked in water for 30 minutes, and the sports floor will be deformed, expanded, and lost its luster. Such sports wood flooring is basically scrapped and should be replaced, and attention should be paid to removing the moisture under the floor and drying it.

4. Precautions.

After the sports wood floor is soaked in water, it is important to pay attention to the fact that it cannot be blown by hair dryer, exposed to sunlight, or dried, which will accelerate the serious deformation and damage to the surface of the sports wood floor of the basketball hall.

It is okay if it is pressed with a heavy object and dried in the shade.

1. Drain the surface water on the floor in the shortest possible time.

2. If it is a small area soaked in water, it is recommended not to pry up the laminate floor to dry, which will easily cause hard damage to the laminate floor, and it is likely to cause serious consequences that cannot be restored. The best thing to do is to quickly remove the baseboard from the floor to expose the expansion joints, which can be used to dissipate the moisture, which usually takes about three to ten days to dry depending on the amount of water seepage.

3. At the same time, you can also use a vacuum cleaner to absorb water vapor in the splicing gap of the soaked floor, or take a hair dryer to dry it with cold air, but do not use hot air to blow it to prevent the surface from drying out and deforming due to heating and drying.

4. If it is a large area of soaking water, the floor after-sales service office should be notified in time, and the floor should be carefully pried up under the condition of keeping the floor not deformed, and placed in the ventilation place according to the "well" shape.

Hello, 1. Remove the baseboard. After the floor is soaked in water, the baseboard on the wall needs to be removed first to ensure that the floor has space when it expands. 2. Dismantle the floor.

Remove the heavily soaked floor and pry it off along the edge of the baseboard. Note that when removing the solid wood floor, you need to start from the foot of the wall. 3. Dry.

Stack the floor in the form of tic-tac-tac-toe rolls, and put a weight on top of it, and put the eggplant in a dry and ventilated place to wait for natural drying, or you can use a fan to assist drying. 4. Blow dry with a hair dryer. In order to avoid dampness inside the floor, it is recommended to use a blow dryer to target the gaps in the floor for drying.

Don't worry if you have a large area of water on the floor, you can use a fan to dry the open floor and the floor that is only soaked in water. Usually soaked in water for no more than 12 hours, good quality solid wood flooring with first aid treatment can be restored after drying.

For the floor after soaking in water, it is important to leave the entire floor as dry in the shade as possible without deforming.

After the surface part of the floor is wiped dry, it can be stacked according to the shape of the word "well", and the weight of the part generated by the superposition of the sail can be used to prevent the occurrence of deformation.

At the same time, it should be noted that it should not be exposed to the sun, it should be placed in a ventilated place to dry, and under normal circumstances, it can be used again for solid wood and multi-layer solid wood with better quality. In addition, in the event of water leakage, the floor after-sales service office should be notified as soon as possible, and the staff will provide consumers with the best solution based on the floor's own situation.

Although the expansion coefficient of laminate flooring is not as high as that of solid wood flooring after soaking in water, it also needs to be handled with caution. For large areas of soaking, similar to solid wood flooring, it is best to remove the baseboards around the laminate floor as soon as possible, warp off the soaked floor, raise it with bricks or other things, and stack the floor in a "well" shape to dry. Generally speaking, the composite flooring can be paved with acacia hail after drying.

Daily ways to prevent soaking in the floor

1. Pay more attention to closing doors and windows: If the floor is soaked because the windows are not closed due to rain, the owner will not be able to get any compensation for losses. Therefore, in typhoon weather, pay attention to close doors and windows to prevent rain. When you go out, you should also pay attention to locking the doors and windows.

2. Regularly inspect the water pipes: Frequently check the water pipes at home to see if there is any dripping and seepage. If there is heating at home, it is necessary to regularly check whether the heating pipe is leaking, and repair it immediately if it is found.

The connecting water pipes between the kitchen and bathroom at home must not be greedy for cheap, so as to avoid accidents when buying fake and shoddy products.

3. Check the air conditioning and other equipment at home: In order to avoid water immersion in the floor due to internal water leakage, you should regularly check the air balance, water dispenser and washing machine at home to see if there is any dripping and leaking.

Most people will choose wooden flooring when decorating indoor flooring, but wooden flooring can not enter the water, recently a friend asked, wooden flooring soaking water bulging can also recover on its own, today will be answered for you, want to know friends may wish to take a look at it!

1. Can the wooden floor recover on its own if it is soaked in water and bulging?

The bulging of the wooden floor after soaking in water cannot be restored. In addition, if the wooden floor is installed without cleaning the floor, it is easy to cause the ground to have sand particles and cause unevenness, and then after people step on it for a long time, the moisture-proof film in the floor and the balance layer on the back will be damaged, resulting in the phenomenon of floor bulging.

Second, how to repair the floor soaked in water and bulging.

1. Disassemble and ventilate and dry.

At this time, it is necessary to disassemble the bulging and the surrounding planks for ventilation in time, so as to alleviate the phenomenon of arching on the ground, and wait until the moisture of the floor has evaporated, spread the floor back, and leave a small gap as the space for the floor to expand and shrink.

2. Remove the debris of the expansion joint.

If it is only a gap between the floors that is blocked and causes blistering, you need to clean the stains in the cracks to recover.

3. Grinding and repair.

If the blistering area is less than 2cm, the blistering area can be repaired by sanding, but it should be noted that the color and texture should be consistent with the surroundings.

4. Replace the wooden floor.

If the blistering area is relatively large and cannot be repaired, it is necessary to replace the new wooden floor, especially for the laminate floor, once the package must be replaced with a new floor, and then the ground is paved with cement after the cavity is large, and then the new floor can be installed.

Summary: The above is to share for you the wooden floor soaked water drum can still recover on its own and how to repair the floor soaked water bulging, I believe you also have a corresponding understanding after reading the above sharing, if you need to know more about it, please continue to pay attention to Qeeka Home**, will answer for you one by one.