How to properly fasten your seat belt when working at height

Proper way to fasten your seatbelt:1) To tighten the belt, the waist buckle assembly must be fastened and straightened;

2) When using the safety belt for suspension operation, the hook should not be directly hooked on the safety belt rope, but should be hooked on the hanging ring of the safety belt rope;

3) It is forbidden to hang the seat belt on components that are not firm or have sharp corners;

4) Use the same type of seat belt, and each component cannot be replaced without authorization;

5) Seat belts that have been subjected to severe impact should not be used even if the appearance has not changed;

6) It is strictly forbidden to use seat belts to transfer heavy objects;

7) The seat belt should be hung firmly and reliably above, and the height should not be lower than the waist.

Safety management measures: In order to construct the project.

Prevent the occurrence of accidents caused by falling from heights, ensure the safety of construction, and ensure the safety of workers.

Personnel must be assigned by the project department before the operation.

Carry out safety knowledge education, safe operation procedures, and regulations for working at height for its teams.

Special Assignments. Personnel must be certified to work, and the technical person in charge shall make a safety technical disclosure before the operation.

and sign the formalities. Before the operation in the construction area, the construction team leader shall inspect and accept the safety protection facilities, and the operation can only be carried out after the experience is qualified, and the safety officer of the project department shall be reported to the safety officer in time if there are potential safety hazards.

to exclude.

When working at height, you must wear two safety belts on your safety jacket, and the first job after arriving at a high place is to tie a safety belt in a secure place, and the safety belt should be hung high and low (that is, the seat belt is higher than the position of the person).

If you need to remove the first seat belt, you must first attach the second seat belt.

The seat belt must be fastened to a fixed object.

Summary. Hello dear, the correct wearing and use of safety belts for aerial work are as follows:1

Choose the right seat belt: You should choose the right seat belt according to the work environment and needs, including waist belts, chest belts, full-body seat belts, etc. 2.

Wear the harness: Wear the belt part of the harness around the waist and pass the shoulder strap part through the shoulder, then insert the buckle of the harness into the buckle and tighten it. 3.

Install the safety rope: Attach the safety rope to the safety belt and make sure the safety rope is firmly attached to the anchor point. 4.

Check the seat belt: Before working at height, you should carefully check that the seat belt is secure and whether there is any damage or wear. 5.

Use seat belts: When working at height, the seat belts should always be tightened and avoid excessive relaxation or tension. 6.

Regular inspection and maintenance: Regularly check the wear and tear of the seat belt, damage and other conditions, and replace or repair it in time.

Hello dear, the correct wearing and use of safety belts for aerial work are as follows:1Choosing the Right Seat Belt:

The appropriate seat belt should be selected according to the working environment and needs, including waist belts, chest belts, full-body seat belts, etc. 2.Wear a seat belt:

Wear the waistband part of the harness around the waist and pass the shoulder strap part through the shoulder, then insert the buckle of the harness into the buckle and tighten it. 3.Install the safety rope:

Attach the safety rope to the harness and make sure that the safety rope is securely attached to the anchor point. 4.Check your seat belts:

Before proceeding with the high-altitude calendar, you should carefully check whether the safety belt is firm and whether there is any damage or wear. 5.Use seat belts:

In working at height, the safety belt should always be tightened to avoid excessive relaxation or excessive tension. 6.Regular inspection and maintenance:

Regularly inspect the wear and tear of the seat belt, damage and other conditions, and replace or repair it in time.

In short, the correct wearing and use of safety belts for aerial work can effectively protect the safety of aerial workers and reduce the occurrence of aerial work accidents. At the same time, high-altitude workers should also receive relevant training and guidance to improve safety awareness and skill level to ensure the safe carrying of dust at heights.

In the working environment of the beam, working at height is a more dangerous environment, which may cause serious accidents and injuries. Workers must fasten their safety belts when climbing or working at height.

Principles for the suspension of safety belts for working at height.

1. If there is no fixed hanging place for high-altitude work, wire rope of appropriate strength or other methods should be used to hang it. It is forbidden to hang on objects that are moving, with sharp hook angles, or are not secure.

2. High hanging and low use.

Hang the seat belt at a high place, and people working below it are called high hanging low use. It can reduce the actual impact distance when a fall occurs, as opposed to hanging low and high. Because when the fall occurs, the distance of the actual impact will increase, and the human fiber and rope will be subjected to a large impact load, so the safety belt must be hung high and low, and the low hanging and high use must be eliminated.

3. The safety belt should be tied to a firm component or object to prevent swinging or collision, the rope should not be knotted, and the hook should be hung on the connecting ring.

Before use, workers must fully ensure that they comply with the instructions for the destruction and sale of each component of the product, and make the protective equipment special. Users are trained to ensure that they are familiar with and able to use safety belts for working at height.

1. Every time you use the safety belt, you should check the sign and certificate, check whether the nylon has cracks, whether the stitches are reliable, whether the metal parts are missing, cracks and corrosion, and the safety rope should be hung on the connecting ring.

2. The seat belt should be hung high and low, and prevent swing and collision, avoid sharp substances, and not contact open flames.

3. The hook and loop of the safety belt should be firmly hung on the tethering point during operation.

4. When using the seat belt in a low temperature environment, pay attention to prevent the seat belt from becoming hard and cracking.

Summary. Seat belts should be fastened when working at height, whether or not they are in a safe aisle.

Whether it is possible to work at height without wearing a seat belt in the safety aisle.

Seat belts should be fastened when working at height, whether or not they are in a safe aisle.

Even within the safe passage, there may be high-risk areas or unexpected situations, such as **, fire and debris disasters, etc., which can pose a threat to workers. If you don't wear a seat belt, you will be in great danger to your workers in the event of an accident.

Whether there are corresponding specifications.

Some kisses. 1.GB 50883-2013 "Regulations for Safety Supervision of Special Equipment" This standard clarifies the definition, classification, and management requirements for high-altitude operations, including preparation and preparation before the first operation at height, on-site safety measures, personal protective equipment, and operation methods.

2.GB T 19001-2016 ISO 9001:2015 "Quality Management System Requirements" This standard stipulates the basic requirements for enterprises to establish a quality management system, including risk assessment, operation procedure formulation, training plan, etc.

Roll the tracks. 3.JGJ 80-2017 "Technical Code for Building Construction Safety" This standard stipulates various safety technical requirements in building construction, including safety measures, protective measures, inspections and records for working at height. 4.

JT T 1099-2018 "Technical Code for Safety in Highway and Bridge Maintenance and Construction" This standard provides detailed provisions for the safety issues in the construction of highway and bridge maintenance, including safety measures for high-altitude operations, safety protection for high-altitude workers, etc.

These norms and standards are formulated to ensure the safety of people working at height, and enterprises and individuals should strictly abide by them when working at height.

Can you send the relevant provisions on working at height in the specification?

The following are the relevant regulations in China's "Safety Regulations for Working at Height":1Work at height must be carried out on specially set up work platforms, scaffolding, protective railings, safety nets and other facilities.

2.When working at height, it is necessary to wear a safety belt that meets national standards and use it correctly. 3.

Before working at height, the workplace must be inspected to ensure that it is safe and reliable. 4.It is forbidden to work at height under severe weather conditions such as wind force greater than level 6 or thunder and lightning.

5.When working at height, it must be commanded and supervised by personnel with the qualifications of the stool, and equipped with necessary safety warning signs.

6.It is forbidden to allow hail cress to work at height with unsatisfactory or damaged equipment, tools and materials without careful inspection and confirmation. 7.

When working at height, the operating procedures must be observed, and it is strictly forbidden to overload the use of lifting machinery or other dangerous equipment. 8.When working at height, it is necessary to pay attention to the surrounding environment and personnel safety to avoid causing injury to the surrounding environment and human hands.

A cost-effective car starts with excellent safety features. The most basic safety feature of a car is the seat belt. How to use seat belts correctly? Here it is necessary to explain clearly.

When the car collides or encounters unexpected emergency braking, the huge inertia will cause the driver and passengers to collide with the steering wheel, windshield and other objects in the car for the second time, and even throw the driver and passengers out of the seat or the car, causing serious injury. At this time, the seat belt can firmly fix the driver and occupants on the seat and prevent secondary collisions.

Although the use of seat belts is simple, many drivers and passengers cannot use them correctly, which leads to adverse consequences. In order to ensure the safety of the driver and passengers, the following points should be taken into account when using seat belts:

Always check the condition of your seat belt and replace it promptly if you notice any damage. All bolts on the floor next to the chair should be tightened as required, and sealant should be applied around the bolts.

Second, wear your seatbelt properly. The three-point belt should be tied as low as possible, at the hips, not at the waist; The shoulder straps should not be placed under the arms, but should be hung diagonally on the chest. Drivers and passengers should not twist their seatbelts when using them.

Third, don't let the seat belt press against hard or fragile objects. For example, glasses, pens, and keys in clothes; Do not allow the seat belt to touch sharp objects to avoid damaging the seat belt; Do not allow the back of the chair to tilt too much, otherwise the seat belt will not be able to extend and roll up properly; When the seat is empty, put the seat belt back into the retractor. (Han Xu).

The current national standard seat belt standard GB6095-2009,

Seat belts should be hung high and low, and attention should be paid to prevent swing collisions. The length of the safety rope is limited, and a buffer should be added when using a long rope of more than 3m. It is not allowed to use the rope in a knot, nor is it allowed to hang the hook directly on the safety rope, but should be hung on the connecting ring.

The various parts on the seat belt should be sampled once after more than 2 years of use.

The correct way to use the seat belt barricade:

1. Pick up the deadbolt and pull the seat belt through your body.

2. Insert the deadbolt into the lock until you hear a "click", and then pull the seat belt to confirm that the lock pin is missing.

3. Pull the shoulder strap upwards to tighten the hip strap (the hip strap is at the hip bone, not the abdomen).

4. Check the position of the seat belt, press the height adjuster of the seat belt, and adjust it to the appropriate position.