What are the precautions for each step of paving floor tiles?

Pay attention to these points when paving: 1. The floor must be fully haired, and then brushed with a clean cement slurry. Be careful not to collect water to prevent seepage downstairs through the seams of the slabs.

For those with drainage slope requirements, such as toilets, bathrooms, etc., the slope direction of tiling should be controlled according to the corresponding slope pull line. The surface is smoothed and checked with a 2m ruler, and the deviation shall not be greater than 5mm, and the elevation deviation shall not be greater than 8mm. There shall be no scratches, missing edges and corners and other quality defects on the surface of the veneer.

Expired and agglomerated cement should not be used as a binder. Before laying the floor tiles, all the floor tiles must be unpacked and selected. Before paving, the floor tiles should be carefully measured and then typeset by computer as much as possible, and a reasonable plan should be selected.

2. The mortar uses cement mortar volume ratio, the adhesive layer shall not be less than 12 thick, the mortar is full, and the cement is uniformly used with cement from large factories. Light-colored granite and marble should be hung with white cement to prevent overcoloring. Before paving, the floor tiles should be soaked in water and dried to achieve dry outside and wet inside, and there is no water trace on the surface, and the color is selected for use.

Before paving, the cross line should be pulled in the horizontal and vertical directions, and the horizontal and vertical lines must be guaranteed to be penetrated when paving, and no staggered seams should be allowed. When the floor tiles are laid, they should be cleaned as they are paved and kept clean at all times. The cement mortar in the brick joint is cleaned, and the joint is carried out before the completion of the joint, the joint is cleaned first, and the putty is adjusted with white cement and talcum powder, and the jointed putty is lower than the brick surface 1.

3. When the floor tiles are paved, other types of work shall not be polluted, shall not be stepped on artificially, and the joints shall be cleaned within 24 hours, and shall be cleaned as soon as they are done, and shall be maintained, and it shall be forbidden to go to the master within two days. In order not to affect the construction of other projects, solid wood planks can be laid on the ground for people to walk. After the floor tile is laid, after checking that there is no flatness error, hollowing, color difference, etc., cover and protect it with thick cardboard, the iron nails on the cardboard must be removed, and the cardboard and cardboard must be pasted tightly with sealing glue to prevent debris from entering.

It is strictly forbidden to use water when there is no drainage or stagnant water equipment, especially to prevent soaking the cardboard used to protect the floor tiles, so as to prevent indirect pollution of the floor tiles. Foundation filling, such as flower ponds and toilets, is filled with moist concrete and carbon slag, so that the filling is dense, firm and reliable, and lightweight.

Precautions. 1. The laying temperature of floor tiles should be higher than 10 or more. Before laying, the floor tiles must be placed face down on the construction site for more than 24 hours so that the temperature of the floor tiles is the same as the room temperature. The room temperature should be kept as constant as possible during the laying process.

2. In addition to squares, floor tiles can also be cut into triangles, rectangles and other shapes at will.

3. Before laying, first draw a cross-shaped baseline on the ground. The method is: measure the size of the ground, draw a longitudinal or transverse line on the ground, and then make a perpendicular line through the ** of this line.

If the floor tiles are paved diagonally, the reticle should be drawn at an angle of 45° to the original baseline. For best results, the floor tiles at the edges should be at least half of the floor tiles, if less than half, the reticle can be shifted by 1 2 floor tile widths. The floor tiles should be laid from the center of the ground to the periphery.

Floor tiles are a kind of floor decoration material, also called floor tiles. It is made of clay firing. A variety of specifications. Hard, pressure-resistant, wear-resistant, moisture-proof. Some are glazed and have a decorative effect. It is mostly used for the ground and floor of public buildings and civil buildings.

There are many varieties of floor tiles, and there is a lot of room to choose from, which can be divided into glazed tiles, full-body tiles (non-slip tiles), polished tiles, vitrified tiles, etc. As a large-scale floor material, floor tiles use their own colors and textures to create a living environment with different styles.

In today's society, people's work is relatively busy, so when decorating the floor, people will choose as easy to care for as many floor tiles as possible, because in this way, it is not only beautiful in appearance, but also can improve the grade of the home. However, how to lay floor tiles, and what are the precautions when laying floor tiles?

How to pave the ground for the banquet bricks? Take a look at the following steps:

First, before paving the floor tiles, it is necessary to do it in accordance with the requirements of the design drawings, find out the patterns and graphics of the floor tiles and then try to sort them, but to select bad products, which is conducive to the follow-up work.

Second, after the products are in place, they should be classified and placed in a safe place to avoid damage to the floor tiles.

Thirdly, before operation, the floor tiles should be soaked first, so as to avoid it ingesting the moisture in the cement, which will lead to subsequent cracking.

Fourth, before operating, the ground should be drenched, so that the dust can be reduced during operation.

Fifth, before starting, you should use a 1:5 ratio to exchange the mud, then add water to stir, and then spread it on the floor tiles to ensure that they can fit each other.

Sixth, after they are matched, they should be gently patted with a hammer until they reach the guidelines, remembering that the cement oil must be smoothed, so as to avoid the phenomenon of hollowing.

After learning how to lay floor tiles, it is necessary to understand what precautions are taken when laying floor tiles, which are as follows:

1. If it is an old house, then it should be haired first during operation.

2. When selecting floor tiles, the specifications and colors of floor tiles must meet the requirements, and there can be no scratches, defects, and expired products cannot be used.

After reading the above description, everyone must have a certain understanding of how to pave floor tiles, if you want to pave floor tiles, you may wish to refer to how to pave floor tiles.

You can get it for free

When the owners are decorating, they always want to make their floor tiles beautiful and stylish. Nowadays, the old method of laying floor tiles is somewhat impractical, thenA new way to pave floor tiles, things to look out for.

First buy the tiles, and when the tiles, soak for at least 2 hours. The purpose of soaking is to allow the tiles to absorb the moisture more fully, and after the tiles have been completely immersed in water, it is necessary to wipe off the moisture on the surface of the tiles before the laying begins, so that the paving work can be carried out smoothly.

Before you start laying tiles, you need to hang vertical lines on the screed on the wall to determine the dimensions of the tile wall; Then set the horizontal line. The purpose of this is to keep the tiles flat, vertical and flat.

When laying tiles, be sure to use a horizontal line argument as a scale and set a plate that can support the tiles. The purpose of this is to prevent the tiles from moving or falling before they reach the strength of the bond.

1）.In the kitchen and bathroom, the floor must be sloped in order to facilitate drainage.

2）.When laying floor tiles, be sure to pay attention to the treatment of the waterproof layer. Kitchens and bathrooms are especially important for waterproofing.

Because if the waterproofing effect is not good, the floor tiles need to be replaced in the later stage, which will destroy the original cement source stove wheel mortar waterproof layer. Therefore, it is advisable to first lay an asphalt waterproofing layer in front of the floor tiles and fill the tiles with white cement.

3）.The brick surface should be flat, the angle should be accurate, the interface should be on the top, and the tiles should be soaked for half a day before use. Different areas of the floor tile should be chosen differently. For example, floor tiles in the living room should be made of vitrified tiles, as they are hard-wearing, bright and easy to clean.

Laying floor tiles is one of the most important hail letter steps in decoration, so owners must pay attention to the process of laying floor tiles when decorating, so that they will feel comfortable and beautiful in the future, and avoid worries. A new way to pave floor tilesIt is more practical, and I hope it will be helpful to all owners.

You can get it for free

The tiles are packed during the home improvement process, so that the tiles are better packed, and then the tiles and its appearance are packed correctly and a series of very important tiles, these steps will affect the entire indoor environment!

Steps for laying floor tiles, tile quenching, first of all, after the completion of the tile material packaging to prevent the impact of the tile material packaging buy enough clean water tile tile tile well absorb absorbent to absorb moisture, so as to prolong the phenomenon of the decline in the adhesive strength of the floor tile soaked in water within two hours of empty because it will rise, so before laying the tile out of the water and wipe the water surface should be wiped.

Steps for laying floor tiles, set the auxiliary line, which is used to determine the tiles and walls, and set the retention level to ensure that the vertical, horizontal and vertical, splicing process is evenly started packing ceramic hanging vertical size should be hung on the wall.

Steps for laying floor tilesIn the tiling process, the tile board should be placed horizontally to prevent the displacement or phenomenon of the tile from reaching a certain bonding strength before the tile falls, and the support position.

Steps for laying floor tilesIn order, the floor is beginning to see, the pavement tile left to create or the balcony door side of the moving sequence generally includes the following, as mentioned above, the first run is washed with water, and then put into the cement tile, then the tile on the scraper is attached to the back of the horizontal layer to the softened adhesive should be known, if the adhesive is too thick, too thick, too thin to use, fill the tile rubber hammer to strike the gap between the cement wall and the brick, it is not easy to share it too thin, open, and then paste it up is not easy.

Steps for laying floor tilesWhen cleaning, maintenance, contamination is required to be able to clean the surface with a significant local concentration of good packing bricks after cleaning with a 10% dilute hydrochloric acid aqueous solution, the last lift must be washed again with dilute hydrochloric acid and washed with water. Tiles can be glazed if, after cleaning is done also mega mold spray pearl Bailey bleached thin layer on the surface, and with a soft cloth, we maintain the surface gloss and polishing of the tile surface can not be easily contaminated at once. Guess carefully.

Steps for laying floor tilesThe fully immersed floor tiles will absorb moisture before packing the tiles, soak if the floor tiles lack or there is no time to absorb the pavement tiles, then the wet tile cracks must be created in the cement with cavitation phenomena.

2. The quality of cement sand is better, the data lays the tile floor packaging is what, when it is necessary to see, if you have passed the 3C certification, you must choose to buy, *** cement, its life is not to choose the contact product, the life of the river sand is the best choice to choose sand, the paste effect is very good.

3. The first brick must be chosen. When laying floor tiles, the placement and placement of the first brick is very important, which usually affects the packaging effect of the entire floor.

Steps for laying floor tilesThe packing order, the floor tiles can be placed in the living room, so the overall effect of this order is better, you can put your room from the living room to the living room, so that you can prevent the new packing tiles from being stepped on, there is a store. The order of the stickers must be set separately and can reduce the cutting of the tiles.

You can get it for free

Because the ceramic tiles will expand and shrink under natural conditions, the reserved brick joints can avoid the phenomenon of hollowing and falling off due to the squeezing of adjacent tiles; Secondly, it can reduce the problem of uneven joints and uneven paving caused by the size of the tile and the size of manual error. Paving tiles must calculate the size, to avoid the appearance of many different sizes of processing bricks, even if there are processing bricks, it is best to appear at the root of the wall to be placed in the future, so as not to affect the overall aesthetics in the future.

This is not correct, because the surface tooth is uneven and uneven, which will lead to a smaller bonding area between the adhesive material and the tile, and a weaker adhesion force. The correct way is to use the tooth scraper to evenly form a strip-like layout with a toothed scraper on the horizontal base surface. The cutting size and cutting method need to be accurately operated, and how the technology is not skillful is easy to cause the phenomenon of porcelain collapse.

If you are making complex waterjet cutting, it is best to use professional equipment to cut it to avoid large errors caused by manual cutting.

Regarding floor tiles, we often consider its quality, color and type, but we don't know that its collage method can also make the appearance of the home instantly rise several levels. Glazed tiles must be left in accordance with the requirements when paving. If the tile factory is not equipped with a seam clip, we can pave the seam according to the gap of 2mm.

This can reduce the expansion force of the tile due to heat in the future, resulting in hollowing and falling off of the tile.

If you must leave the seam to pave, you can choose to pave and fill the seam or sew it beautifully. The beauty seam is to fill the gap in the tile with a special beauty joint, due to the addition of curing agent in the beauty joint, the tile gap after the beauty seam is very firm, not easy to fall, good waterproof performance, and there are many colors to choose from, if the tile factory is not equipped with a seam clip, we can leave the seam according to the gap of 2mm for seam paving. This can reduce the expansion force of the tile due to heat in the future, resulting in hollowing and falling off of the tile.

The technique of laying floor tiles is to lay from the middle to the periphery, so that the integrity is better, it looks more neat, pay attention to soak in advance, so that the laying will be more firm.

The first step in laying floor tiles is to wet the base with water to remove debris and floating sand. To wipe the bonding layer again, it should be noted that 1:3 dry cement slurry should be used, paved and smoothed according to the horizontal line, and then the bricks should be placed on the mortar and vibrated with a rubber hammer.

At this time, the floor tiles are removed and poured with cement slurry, and then the floor tiles can be put on the ground and vibrate. The dry paving method can effectively avoid the occurrence of hollow drums and bubbles caused by the paving process.