How to set up Tengda W320R wireless router

Here's how to set up your router:

1. Line connection:

a.Connect the network cable of the cat to the router (WAN port), and then connect the network cable of the computer to the router (any port numbered 1 2 3 4).

b.Connect the broadband cable to the router (WAN port), and then connect the network cable of the computer to the router (any port numbered 1 2 3 4).

2. Log in to the router interface.

In the browser, type: Enter, enter in the pop-up page: admin and click "OK".

3. Set up the router to surf the Internet.

Before setting up the Internet access, choose the correct Internet access method: Generally, there are three types as follows:

ADSL dial-up: Usually to access the Internet (when not connected to the router) need to click on the broadband connection, dial-up is successful before you can access the Internet, you should choose the Internet mode, Internet access and Internet password correctly enter the broadband and password, you can.

Automatically obtain an IP address: If you usually surf the Internet (when you are not connected to the router), you only need to set the local connection of the computer to automatically obtain the IP address to access the Internet, you should choose this Internet access method.

Static IP: If you need to fill in a fixed IP address in the local connection to access the Internet, you should choose the Internet access method, log in to the interface of the router, click "Advanced Settings" - "WAN Port Settings" to select the static IP mode "Static IP mode", and enter the fixed IP address, subnet mask, gateway, DNS domain name server and other parameters of the Internet into the correct one.

4. After setting, click "Running Status" - "WAN Status" to check whether the connection status of the WAN port shows that it is connected, and whether the connection mode is displayed correctly.

The corresponding connection mode for ADSL dial-up is: PPPoE

The connection mode corresponding to the static IP address is the static IP address

Enter or in the address bar, enter admin after entering Generally, the password has not been changed, and the initial password is admin Then click wireless, and then click on the setting is OK.

Is there anything you don't understand?

Here are the detailed steps, you can see the wireless routing, how to set up TPLink and how to connect to the second router.

Here are the very detailed steps, you can take a look at the wireless router, Mercury MW300R wireless router setup.

If you need to set the router's wireless signal name or wireless password, please follow the steps below to set it:

2. Change the wireless signal name of the router, in the subsequent page, click "Advanced Settings" - "Wireless Settings" - "Wireless Basic Settings", find "Wireless Signal Name (SSID)", and set the wireless signal name you want (number, letter or combination of numbers and letters) by yourself, as shown in the following figure:

3. Change the wireless password, click "Advanced Settings" - "Wireless Settings" - "Wireless Security", find the "Key", and set the wireless password you want (at least 8 digits, letters or a combination of numbers and letters) by yourself, as shown in the figure below

No matter what you use to access the Internet, the configuration of the router has nothing to do with the equipment at the physical layer, and the access method is the same as your ordinary network cable.

Tengda's wireless routers are very easy to set up!

Enter in the address bar of the browser, open, and then enter the password admin, there is an advanced setting in the upper left corner, open the advanced settings to find the wireless settings. It's all in Chinese, and you can understand it at a glance!

Tengda W303R wireless router setup method:

Home Network Environment Cabling]:

1. There is a cat (modem): cat (modem) - router WAN port; The LAN port of the router --- a computer.

2. No modem: network cable --- router WAN port; The LAN port of the router --- a computer.

Computer enters the router]:

1. The computer IP and DNS settings are automatically obtained.

2. Open the browser, enter the general router address in the address bar is this or check the login information on the back of the router) Enter the route - enter the user name and password, (the default is generally admin).

Set Router Dialing]:

1. In the [Setup Wizard], select [PPPoE Dialing] (some are ADSL dialing), enter the username and password (provided by the network service provider) according to the prompts, and save.

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPPoe Dialing] in the three options of [Connection]. The next step is to select [Auto Connect], Save, and Exit.

Turn on the router's wireless function].

1. Select Wireless Settings --- Basic Settings.

2. Check [Turn on wireless function] and click Save.

Set wifi password].

1. Wireless Settings - Wireless Security Settings - Select [WPA-PSK WPA2-PSK].

Authentication Type: Automatic.

Encryption algorithm: AES.

The PSK password is the wireless password. Set the required password.

Here's how to set it up:

Set the WAN port to auto-fetch, and if it doesn't work, change the LAN to set WAN auto-fetch.