How do you hook the shoes, how do you hook the soles?

Updated on vogue 2024-06-30
9 answers
  1. Anonymous users2024-02-12

    1. First hook the line on the bottom (special line for the bottom - coarse cotton thread or nylon thread).

    2. Use a short needle to hook a short needle on the bottom line, (if you want to stand a little bit, you can use two wire hooks) hook four rows, and the heel does not need to hook four rows.

    3. Weaving the bottom: use two rod needles to weave according to the shape of the bottom, according to the thickness of the wool and the size of the sole, add a needle on both sides of the second row of weaving to form a rounded corner, and add a needle to the width of the weaving point, not too much, the bottom of the weaving is better than the sole is a little smaller, because the wool shrinkage is good and the weaving will be too large and uneven. (In order to weave two insoles into the same, you can use two threads to knit at the same time) The needle is also rounded according to the shape of the bottom.

    4. Sew the woven bottom on the sole: if there is a thin sponge, put two layers under the woolen sole (the sponge and the woolen bottom can be sewn from top to bottom with a thread in the middle).

    5. Needle: the toe of the shoe is facing yourself. To leave a piece of thread slightly longer than the sole, the needle can be started according to the size of the sole, or 7, needle.

    In short, the two sides should not be crooked, but should be equal. (If there is an unevenness on one side, you can separate the braid at the same time, and sometimes you can separate the two braids.) Utility.

    It depends on the high and low). The first stitch is short, then one braid, two medium and long stitches (i.e., one large stitch) in the third braid, two medium and long stitches in the fifth braid, and so on. Hook to the end and hook a short needle, and then hook the remaining thread out of the short needle loop and tighten it.

    Again, the needles mentioned above are all large needles. The first stitch of the medium-length needle in the second row is hooked in front of a large needle in the first row, and the second needle is hooked in the braid needle below, (if the yarn is thin, you can also hook both needles underneath, so that it will be thicker.) The first needle of the medium and long needles in the third row is the same as above, the second needle is hooked in the middle of the two medium and long needles in the lower row, and so on.

    Remember. The first and last stitches of each row are short stitches.

    6. In order to make the upper not high or low, don't hook every braid, but properly separate the braid hook, if each braid is hooked, the upper will be high.

    7. Hook flower: to choose the pattern suitable for the size of the sole, try to hook in the middle, the general size of the pattern is three big needles to start. Note:

    The front and back should be symmetrical, and the front and back should be three large needles. The hook is more than 20 rows, the sole is long, and the number of rows will be more) When changing the color and line, it is changed when there are two medium and long needles and one needle.

  2. Anonymous users2024-02-11

    Hook method for shoes:

    Start by hooking 16 pigtails.

    Take the braid of the first hook as the first stitch and the braid of the last hook as the 16th stitch).

    Start Circle Hook:

    The first round of the second stitch starts with the 13th braid (three braids as the first stitch), the second stitch begins with 5 medium and long stitches, 7 long stitches, and finally 7 long stitches in the first braid. After the 7 stitches are hooked, they turn to the bottom, corresponding to the upper half of the hook, first hooking 7 long needles, then 5 medium and long needles, and hooking 6 medium and long needles in the 13th braid. (Add the one with three pigtails, and there should be 7 stitches in the last stitch as well).

    Note: The first braid is the toe and the 13th braid is the heel.

    The second lap: from now on it's all long needles. Hook 3 stitches of the braid (as the 14th stitch).

    Then hook one stitch in each hole of the first circle, (when you hook the first braid, don't you have 7 stitches in it, two stitches from the needle, two stitches in the fourth stitch, two stitches in the third stitch), and start the second half of the hook (in the 13th stitch, counting the braid, there are also 7 stitches: 2 stitches in the 3rd stitch, 3 stitches in the 4th stitch, and 2 stitches in the fifth stitch).

    Note: The sole hook is finished.

    Continue hooking (upper)! Hook two more circles, the hook method is the same, hook to the second needle (note that it is the toe) hook two needles and then combine the needle (that is, first hook two needles and then merge into a needle), then hook a needle, then hook two needles and needle, and then hook a needle, and so on, hook to the second needle of the lower half of the circle (or the toe part). There is a hole and a needle in the back.

    The last loop: the method is the same as step 4, but when the hook reaches the tip of the second needle, it is: hook two needles and needle, and then hook two needles and needle, there is no separate hook needle.

    Lock a row of edges. Let's hook a shoelace on the side of the shoe. Don't forget to nail a button. A shoe hook is finished!

  3. Anonymous users2024-02-10

    You have to find someone to teach you this question by hand, and you can't say it.

  4. Anonymous users2024-02-09

    Tools Raw materials: coarse wool, crochet hooks.

    1. First of all, prepare the soles of the good line, start to hook a circle of bottom lines from the toe position, and leave a line beyond the length of the sole when hooking.

    2. After a circle of bottom lines is hooked, hook the left tail line into the last stitch, and then tighten the line so that it is fixed (the toe head should be hooked a little tighter, because the line is thicker and the distance will be farther, which is not conducive to starting to hook the upper).

    3. Then pull the main line to the other side, and the line should be hooked a short needle at an angle forward.

    4. Then hook a "medium and long needle" every other needle, and hook a total of "5" long needles on the toe cap (one needle must be hooked forward for each fixed needle).

    5. In the process of crocheting halfway, there will be inconsistencies on both sides, which is a normal situation.

    6. As long as you hook forward a little more, this gap can be flattened.

    7. In the process of crocheting, it is necessary to compare with another crocheted shoe from time to time, so that the two shoes can be the same.

    8. And when the hook is in the middle position, two needles should be fixed forward, and both sides should be consistent.

    9. When hooking to the back rows, tighten the line appropriately to avoid the cuff being too fat.

    10. In the last few lines, hook three stitches backwards, so as to show the arc of the slippers, and pay attention to the consistent position of the edges of the two shoes.

    11. When the slippers are hooked to the last line, this row does not hook the medium and long needles, but instead hooks a short needle.

    12. Cut the thread after the hook is completed.

    13. Hide the thread again.

    14. a finished product.

  5. Anonymous users2024-02-08

    The specific steps to hook shoes are as follows:

    1. The first step is to use the awl of the shoe to put a strong thread on the sole.

    2. Sew the insole to the sole with a needle and thread.

    3. Start the needle from the front of the sole and hook two short needles.

    4. Thread the yarn in the front of the sole.

    5. Hook the upper with a double long needle, repeat the above steps until the required length, and weave to the last needle, that is, complete the specific operation of hooking the shoe.

  6. Anonymous users2024-02-07

    How to hook shoes:

    Preparation materials: soles, wool, crochet hooks.

    1. First of all, the hook shoes must first choose the sole of the sole, and it is best to buy the one that has been on the line, which is convenient.

    2. Then use a short needle to hook the sole of the shoe, and the size is about the same as that of the sole. Once the hook is complete, continue to hook a short circle of needles around it.

    3. Then put the finished bottom surface to the sole. Remember that the number of needles must be evenly distributed.

    4. Next, hook two short needles at the junction between the edge and the center of the sole.

    5. Then you can hook the upper. Start by hooking six to seven sets of medium or long needles (two needles each) on the toe cap, leaving enough length of thread on the left side to close the needle.

    6. The first four or five lines of the last toe toe, the starting and closing needles of each row should be close to the front row, and the starting and closing needles of each row in the back should be spaced one needle, and the hook will be hooked until the celebration is accompanied by a friend.

  7. Anonymous users2024-02-06

    The hook shoe tutorial is as follows:

    Material preparation: wool, needle, etc.

    Operation steps: 1. First lay the foundation, the starting point is selected on the side of the shoe, the crochet needle is passed through the bottom line, hooked the wool, and then the line is hidden from the bottom line under the hook and roll. Hook the wire, pull it out of the coil, and pull it tight appropriately.

    2. Hook the thread out from the bottom line, wrap the thread around the Jun needle, and pull the thread out from the two coil halls. This is a short needle method, and the bottom line is hooked in a circle with the same needle method.

    3. Start crocheting the upper and thread the crochet needle directly through the adjacent pores. Wrap the thread around the crochet needle, hook the crochet needle to the winding, and pull out the pores from the end of the thread to form 2 coils. Hook the previous one through the back one to form a coil.

    4. Hook the crochet needle to the end of the thread, stretch it through the coil, and remove the crochet needle. Pull the thread tight, but don't cut it yet. The first row of the upper is hooked.

    5. Start hooking the second row of stupid relatives, and the position of threading the needle is on the right side of the first row of needle holes, separated by 1 pinhole. The wire is taken out of the pore to form a coil. Wrap the thread around the crochet needle, take the thread out of the coil, tighten it appropriately, and complete the second row of needles.

    6. When collecting the needle, thread the crochet needle into the holes of the second space, and the stitching method is the same as that of the first row.

    7. Then it is the same method to hook the rest, you can add patterns, novices are recommended to hook without flowers to try the hand.

    8. A slipper is hooked.

  8. Anonymous users2024-02-05

    Tutorial for hooking shoes:

    1. First of all, we need to lay the foundation, the starting point is on the side of the shoe, the crochet needle is passed through the bottom line, hooked the wool, and then hooked the line out from under the bottom line. Hook the wire, pull it out of the coil, and pull it tight appropriately. Laugh wide.

    2. Then hook the thread out from the bottom line, wrap the thread around the crochet needle, and pull the thread out from the two coils. This is a short needle method, and the bottom thread is hooked with the same needle method.

    3. Then start crocheting the upper and thread the crochet needle directly through the adjacent holes. Wrap the wire around the crochet hook to the light, hook the crochet needle to the winding, and pull out the pores from the end of the thread to form 2 coils. Hook the previous one through the back one to form a coil.

    4. Then hook the crochet needle to the end of the thread, stretch it through the coil, and remove the crochet needle. Pull the thread tight, but don't cut it yet. The first row of the upper is hooked.

    5. Next, start to hook the second row, and the position of the needle threading is on the right side of the first row of needle holes, separated by 1 pinhole. The wire is taken out of the pore to form a coil. Wrap the thread around the crochet needle, take the thread out of the coil, tighten the pin width appropriately, and complete the second row of needles.

    6. Then when collecting the needle, the crochet needle is inserted into the holes of the second space, and the stitching method is the same as that of the first row.

    7. Finally, it is the same method to hook the rest, you can add patterns, novices are recommended to hook the flower first, and a slipper will be hooked.

  9. Anonymous users2024-02-04

    The easiest tutorial for beginners to hook shoes is as follows:

    The first loop: Loop, crochet 8 short needles in the ring, and finally pull it upright: first pull out the crochet needle, then thread the first short needle from back to front, then thread the last coil at the same time, and pull it out from behind, then pull out the crochet needle, and then re-insert it.

    The second circle: 1 lock, 1 short needle in the middle of the needle that is inserted, and then 1 short needle in the left vertical braid needle, and each needle in the back is hooked like this (pick the braid needle hook 1 short, and then thread the left vertical braid needle in the hook 1 short).

    Note: When we thread the vertical braid needle, turn to the reverse side and look at it, making sure to thread it in the middle of the 2 threads of the braid needle; The final pull method is the same as on the first lap.

    The third circle: a circle of short needles without adding or subtracting hooks (every 1 needle is threaded into a vertical braid needle to hook, and the crochet short needles mentioned in each subsequent circle are threaded like this).

    Lap 4: Add 1 stitch on each side of the toe cap (the same method as in the 2nd lap).

    Note: If you think the shoe size is enough, we will always repeat the hook method of the 3rd lap from the 4th lap, without adding or subtracting the loop hook, until the desired depth of the toe (the demonstration depth is for your reference).

    After hooking to the desired depth, row 1: Hook 7-needle short needle; Row 2: 1 lock, turn over (the back is a back and forth flip hook), this row picks 2 needles in the middle of the vertical braid needle, hooks out 6 short needles, and the 7th needle we pick 1 short needle in the side (as shown in the figure); Line 3:

    It is also threaded in the middle of the 2 stitches, and the last 1 stitch is also a short stitch on the side of the hook; Lines 4-5: Repeat the hook in lines 3-4.

    Line 6: Skip the first stitch, followed by no addition or subtraction; Line 7: Also skip the first pin to dehook; Lap 8 (to pick a hook around the edge):

    After a row of hooks is verticalized, we pick the side of the heel, and the two sides are 1 short needle for each row of hooks, the last 1 needle on the side, and the needle where the toe and the side intersect, these 2 needles are crocheted together 2 and 1; There is no addition or subtraction at the toe cap.

    Lap 9: A short needle with a hook (the way to thread the needle is still the same, don't forget). The 10th circle: change the color of the line, and then do not add or subtract the remaining eggplant hook to pull the needle (this circle is a normal needle hook). When it's all done, this simple home slipper is complete!

    That's it for the tutorial, you can give it a try!

Related questions
5 answers2024-06-30

1. Soak all the shoes first, and then use a brush to clean the soles first. >>>More

7 answers2024-06-30

There are two ways to caulk cultural wall tiles:

1) Feed the joints with an ash spoon: put the cement mortar (fine sand: cement = 1:2) on the ash board, smooth it into a slurry board about 5mm thick, and then divide it into 5mm 5mm strips with an ash spoon, send it to the brick joint, wipe the excess mortar on the brick surface, and try to avoid the cement staining the brick surface. >>>More

19 answers2024-06-30

It may have been brought up through clothing.

2 answers2024-06-30

1. According to Sima Qian's "Historical Records", Gou Jian died of illness. In 494 BC, Goujian, the king of Yue, was defeated by the Wu army in Fujiao and was forced to sue for peace with the king of Wu. After three years of herding cattle and sheep for King Wu, he returned to the Yue Kingdom. >>>More

2 answers2024-06-30

If it is only used for communication with foreign guests, then one year is enough. First of all, you can start with the most basic daily oral communication, and then go deep into the specific aspects and memorize them in different categories. When studying, listen more, talk more, and connect more. >>>More