Siemens front loading washing machines show that the load does not enter the water

Fault analysis: according to the washing machine does not enter the water fault, according to the parameters on the Siemens washing machine maintenance manual to carry out the detection from simple to difficult, as the name suggests, first of all, you should check whether it is a power outage or the fuse at home is blown out, after excluding this, and then check whether the water is stopped or the water pressure at home is too low, or it is possible that the water inlet pipe is connected, whether the faucet is opened, whether the power switch is pressed, or the start button is not pressed after pressing, these are external detection methods, Of course, the internal inspection must be operated by our professional and technical personnel, such as whether the filter screen on the inlet valve is too dirty and blocked, and the motor coil of the water inlet solenoid valve is damaged.

Troubleshooting: Based on the analysis of the above professional maintenance staff of Siemens washing machines, it can be known that after eliminating some external faults that are considerable to the naked eye, the water inlet solenoid valve is 100% damaged, and the same model solenoid valve can be replaced, and the test machine can be normal.

The drum washing machine originated in Europe, and the washing method is designed to imitate the principle of beating clothes with a stick hammer. The drum washing machine is made of stainless steel inner barrel, mechanical program controller, phosphating, electrophoresis, spraying triple protection of the shell, and a number of bulky cement blocks to balance the huge centrifugal force generated when the drum rotates to do repetitive motion, plus the joint action of washing powder and water to make the clothes clean. Because the materials used are mainly made of steel, the life span is generally about 15 to 20 years.

This is caused by a malfunction of the control chip, and this part can only be replaced. And it must be an original accessory, so you have to contact the seller and contact the manufacturer's authorized repair point. If it is free during the warranty period, it is estimated that it will be about 200-300 after the warranty period.

Check whether the water inlet is normal, the down sweater is difficult to wash, reduce the ps This washing machine seems to wash two pieces of clothes that can't be washed to wash a bunch because it is easy to deviate.

This is caused by the failure of the control chip, which generally cannot be repaired, and can only be replaced. And it must be an original accessory, so you have to contact the seller, through them to contact the nearest manufacturer's authorized repair point, and they will deal with it. As for **, if it is within the warranty period, it is free, and it depends on the specific situation after the warranty period.

It is estimated at around 200-300.

After the washing machine start program 1] Check whether the door lock switch has electricity; If there is electricity; Look again to see if the door lock is locked; It's not locked; Replace the door lock switch; 2] If the door lock is out of power; inspect the computer board; See if the computer board has powered the door lock switch; 3] When the door lock switch locks the door, lock the door; The door lock switch feeds back the signal to the computer board; 4] The computer board sends power to the water inlet valve; Open the water inlet valve; Fill the washing machine with water; Check one; Check if the inlet valve has electricity; There is electricity; replacement of the inlet valve; 2] No electricity; Check whether the door lock signal has a feedback signal to the computer board; 3] No signal; Check whether the door lock switch is electrified; whether the door lock is in good condition; 4. Check if the computer board is good.

1. The faucet is not turned on, which is a very basic problem, but it happens to be easy to be ignored by everyone. 2. The water pressure is too low, which also causes the problem of not entering the water. 3. Due to the blockage of the inlet valve, the water flow cannot pass through in time.

4. After the water inlet fails, it will directly lead to no water ingress. Suggested treatment: 1. The faucet is not turned on is a very easy problem, it may be that other members of the family have turned off the inlet faucet of the washing machine, or the relevant water inlet valve is closed, at this time this most basic problem should be re-checked.

2. After the faucet is opened, if you want to enter the washing machine, you need a certain pressure, if your own water pressure is not enough, it is likely to lead to the problem that the washing machine does not enter the water or the water enters too slowly. In this case, you should contact the person in charge of the community, or the area. 3. Long-term use is very likely to cause the water inlet valve of the washing machine to be blocked, because it is difficult to ensure that the water stains in many places are very clean.

Then you can clean the filter first, dispose of the dirt attached to the surface, and you can use it normally. 4. If the water purifier in the control panel is faulty, you should contact a professional maintenance master to check it and replace it in time.

The reasons may be as follows:

1. The belt is broken or falls off.

2. The motor fixing screw is loose, causing the belt to slip.

How to use the front-loading washing machine:

1. Preparation for laundry: The material box of the drum washing machine has three slots, which are used from left to right for putting the main detergent, softener and pre-detergent. The main detergent generally refers to laundry detergent, if you wash wool products, you can put a special detergent here; The fabric softener should be put into the middle slot, and the washing machine will release it into the bucket at the appropriate time; Pre-detergents are not usually used too much, mainly referring to soaking agents before formal washing, such as clothing sizing agents and dyes.

All detergents must be dispensed before the start of the laundry program. Once the process starts, the tap water from the inlet pipe is first introduced into the bin, and then from the box into the drum, so that the water flow flushes the diluted laundry detergent into the drum.

Second, the choice of laundry program: the scope of application of each program introduced in the washing machine manual is only a reference, and it is best to choose flexibly according to the dirty program and easy-to-wash program (i.e., material) of the fabric when using. In the daily washing of the family, except for dirty, heavy fabrics and more expensive and fragile fabrics, all kinds of fabrics are not classified according to the material, but all kinds of fabrics are washed together, and the chemical fiber fabric program or standard washing program should be selected.

In the summer, when washing all kinds of relatively light fabrics that are not dirty, you can choose the wool fabric program or the weak washing program. It is necessary to choose a cotton program only when washing dirty, heavy fabrics of all kinds. Dirty woolen knits can also be washed using the synthetic fabric program or the standard washing program.

The wear rate of the drum washing machine on the washing is only a fraction of that of the drum washing machine, and the fabrics that can be washed in the drum washing machine can be washed more in the drum washing machine. The laundry program is divided into 4 categories: cotton fabric, chemical fiber, wool, and super soft. Each type of program offers a different water temperature to choose from.

There are many reasons why it does not rotate, such as the failure of the computer board, motor, circuit, etc., and the symptoms you mentioned will appear.

The biggest possibility is that the washing motor is broken, try to power on the washing motor alone!

1.Is there too much stuffing in your clothes? Resulting in severe imbalances.

2.Is the belt in the back falling off? Open the back cover and take a look. If it comes off, you can install it from the beginning.

The motor of the washing machine is broken and needs to be repaired.

If there is a sound, it means that there is a problem with the motor, and if it is fully automatic, you have to call someone to fix it.

About 99% of the drive belt is loose.

Is the unit plugged in, is the clutch checked or is there a problem with the execution circuit.