How to do the floor tile seam What should be paid attention to in the tile seam

With the improvement of people's living standards and the change of aesthetic concepts, the home decoration.

The requirements are getting higher and higher. According to our previous ordinary decoration method, the tiles are laid in the house.

There will still be gaps, which is not good-looking. Now there is a new ceramic tile seam process, which can optimize this problem, and the tile seam can beautify the tiles that have been paved, and the effect is very good, which can make the decorated tiles more neat, durable and beautiful. But the construction process.

Tile sewing method

1. Tool preparation: glue gun, wallpaper.

Knife, silicone scraper, small bucket.

masking paper; 2. Choose tile grout.

Color: generally it is determined by the customer according to his preference;

3. Operation steps: poke a hole in the mouth of the tile joint agent bottle, then screw on the discharge nozzle, and then use a wallpaper knife to cut the discharge nozzle into a 45-degree angle, the tile joint is less than 2 mm, and the front end of the discharge nozzle can be cut out of the slope angle with a wallpaper knife; If the tile joint is larger than 2 mm, it can be cut off a little more; The width of the discharge nozzle should be less than the width of the seam to ensure that there is no overflow;

4. Construction method:

1) Clean the scene after entering the site, and then use a wallpaper knife to clean the filler in the tile joints and on both sides, and the ground.

Floating dust is not allowed;

2) Quickly wipe the tile joint with a sponge dipped in water, confirm that there is no dust, use a glue gun to evenly hit the material in the brick joint, apply about 1 meter, and block the discharge nozzle;

3) Then use the silicone board to scrape the material immediately, a small amount of material overflowing on both sides of the brick joint, wipe off with a slightly damp sponge, wipe it several times, and the sponge should be cleaned with water frequently;

4) Wait for an area to be done once and then hit it a second time from the beginning to ensure the quality of construction;

5. Construction quality standards: it is necessary to be smooth and not edged, there can be no bubbles, there can be no small pits, the brick surface is not allowed to overflow, and the ground is as clean as new before leaving;

6. If the customer is afraid that the overflow on the brick surface will not be clean, then you can use masking paper to stick to the edge of the brick joint, and then use a glue gun to beat the material, scrape it flat with a scraper, and wait for the material to dry, and you can open the masking paper after repairing.

Precautions for tile seams

1. Ensure that the bottom surface of the construction tile joint must be smooth, strong, dust-free and not wet;

2. The width of the discharge nozzle is slightly less than the width of the joint, so that the discharge can completely cover the bottom surface of the tile gap;

3. The discharge should be uniform, less should not be more, and the small bricks with many cross interfaces should be scraped lightly;

4. The construction temperature is 15-30 degrees, and the overflow must be cleaned up while construction;

5. Within 3 hours of ground construction, do not walk around on it to avoid dirt polluting the surface of the sewing agent.

Summary

The technical requirements for the construction of ceramic tile seams are quite strict, to be very careful and patient, and the materials selected are also good, otherwise the effect of decoration will be the same as not doing beautiful seams, so it is necessary to choose some familiar old employees or find a decoration company.

Help is the best, choose a reliable brand in terms of materials, tiles are also widely used at home, since the house is decorated, don't save this step. Tile joints can also prevent tile leakage, easy to clean and many other advantages. If you want to know more, you can continue to ****'s Tuba Rabbit decoration network. Oh.

1. Ensure that the construction base material must be smooth, strong and dust-free.

2. The width of the tile joint should be consistent, and the plastic cross can be positioned, otherwise it will affect the appearance.

3. The mouth of the discharge nozzle should be small, the discharge should be uniform, and there is a small amount of self-overflowing material in the discharge nozzle when the seam is hooked after each scraping.

4. After construction, we must wait until the surface of the sewing agent is slightly dry, and then remove the spillage, and the caulk can be basically cured in 7-10 days.

Ceramic tile is a decoration material used in every family, and laying smooth and clean tiles on the ground can not only increase the decoration of the house, but also bring great convenience to the cleaning in later life. However, the tile will leave a gap when it is paved, and then it is necessary to carry out tile seamping, thenHow to do tile seamsThis? Let's take a look at the methods and precautions for tile seaming.

How to do tile seams

1. Tools preparation: glue gun, wallpaper knife, silicone scraper, small bucket, masking paper.

2. Choose the color of tile grout: Generally, customers determine according to their own preferences.

3. Operation steps: cut a hole at the bottle mouth of the tile joint, then screw the discharge nozzle on, and then use a wallpaper knife to cut the discharge nozzle into a 45-degree angle, if the tile joint is less than 2 mm, cut a small slope angle at the front end of the discharge nozzle with a wallpaper knife; If the tile joint is greater than 2 mm, then you can cut off an extra section; The width of the discharge nozzle must be less than the width of the seam to ensure that no material is wasted.

4. Construction method:

a. After entering the house, the ground should be cleaned, and then the filling in the tile joints and on both sides should be cleaned with a wallpaper knife, and the ground should not have floating dust.

b. Quickly wipe the tile joints after wetting the sponge with water to ensure that there is no dust, use a glue gun to evenly hit the material in the brick joints, apply about 1 meter, and block the discharge nozzle.

c. Then use the silicone board to scrape the material immediately, and a small amount of material overflows on both sides of the brick joint, wipe it off with a slightly damp sponge, wipe it several times, and the sponge should be cleaned with water frequently.

d. Wait for an area to be done once and then hit it a second time from the beginning to ensure the quality of construction.

5. Construction quality standards: It must be smooth and not edged, there can be no bubbles and small pits, and the brick surface can not overflow, and the ground must be clean before going out.

6. If the customer is constructing by himself and is afraid that the overflow on the brick surface will not be clean, then you can use masking paper to stick it on the edge of the brick joint, and then use a glue gun to beat the material, scrape it flat with a scraper, and wait for the material to dry, and you can open the masking paper after repairing.

What are the precautions for tile seams.

1. After the tile is pasted, clean the surface of the tile and the gap, dry and dust-free, and then fill it with this product.

2. Use hard objects to open aluminum bottles.

3. Screw the nozzle on the mouth of the aluminum bottle.

4. Cut the nozzle into a 45-degree angle along the concave and convex top of the nozzle with a knife, and the width of the nozzle is slightly smaller than the brick joint.

5. Pull the bottom pull ring of the sewing agent. Load the sewing agent into the glue gun, and use the glue gun to evenly inject the material into the brick joint.

6. Grind the material flat with your fingers or scraper.

7. Use a wet sponge to clean up the excess material on the surface of the porcelain slag wheel brick.

8. After the construction is completed, the surface is cured within two hours, and it can be used normally after two days.

The above content is the introduction of the methods and precautions of ceramic tile joints brought to you this time for your reference. I believe that after reading this article, you will also have a certain understanding of how to do beautiful sewing, and hope to provide some help to the owners who are carrying out beautiful sewing construction.

1. First of all, the tile gaps need to be cleaned; Hard impurities can be cleaned with a wallpaper knife, and light substances such as dust can be sucked out with a vacuum cleaner. Then, a second layer of white caulk is applied to give the brick joints a uniform background.

2. Then you need to knock off a part of the sewing agent material to the two groups consistently, generally 50 cm need to be removed.

3. Next, use a steel ball or popsicle stick to press the seam, in which the steel ball flattens the seam stick and presses the right angle. Finally, use a shovel blade to remove the waste and wipe it clean with a rag.

During the installation of floor tiles, there will be gaps between the floor tiles. With the increasing number of modern decorative materials, the use of floor tile grouts is becoming more and more frequent. You may ask what are the steps of floor tile joint construction?

There are generally five steps in the construction of floor tile joints, first pre-laying, and then cleaning the gaps and debris between the floor tiles to fill the gaps.

Step 1: Before laying the floor tiles, pre-laying should be carried out and the gap between the floor tiles should be reserved, generally 1 to 6 mm wide and 1 to 2 mm deep. The smaller the gap, the more beautiful the effect, the wider the gap, and after the hook, the whole ground space is very three-dimensional and layered.

Step 2: Before construction, the gaps and debris between the floor tiles must be cleaned. It can be cleaned by vacuuming or with a broom to make the floor tile gaps dry and dust-free and debris-free.

Step 3: First you need to fill the joints and then make the floor tiles aesthetically pleasing. First, use a white cement product to suture the seams.

After construction, use professional tools to press and smooth the cement surface joints on the floor tile surface. During construction, the depth of the gap is guaranteed to be 1 mm; After the joints are filled, it is necessary to wait for the white cement to dry completely. Sewing the structure is necessary, but at the early stage of construction, it is necessary to remove dust from the surface of the floor tiles.

Step 4: Then prepare the glue. First of all, water is needed to wet the floor tiles between the gaps.

It is important to note that the gap needs to be kept clean and dry. Apply fine grain paper and squeeze the glue into the gaps in the floor tiles. After the construction of the floor tile joint is completed, scrape it flat again, and tear off the texture paper while the glue is not completely dry.

Step 5: After drying the glue, wipe off or remove any excess glue, or scrub with a sponge. When building floor tiles, you can start from the corners of the floor tiles, or place furniture areas to avoid unsightly construction at the beginning.

The above is the introduction of the construction steps of floor tile joints, and it is not difficult to find that hook joints, joint filling and beauty joints are all technical activities. In order to make the whole ground smooth and beautiful, it is recommended that the owner invite an experienced master to lay the floor tile joints.

You can get it for free

1. Prepare tools and materials: sewing agent, glue gun, brush, knife.

2. Clean the gaps in the tiles. Remember to clean the gaps in the tiles before beautifying them, otherwise it will affect the overall aesthetics. At this time, we can use a seam cone and a brush to clean it.

3. Paste masking paper. Masking paper is attached to the edge of the tile. Paste the perfect textured paper, and you can start sewing.

4. Install the glue gun. After installing the sewing agent into the applicator, we need to squeeze out the first 40cm of the sewing agent, because the uneven mixing of the sewing agent in this section may affect the later effect.

5. Start sewing. Squeeze the grout evenly into the gap of the tile through the glue gun.

6. Pressing seams. This is where we need to use the seam ball. Seam pressing with a sewing ball can press the sewing agent into the gap smoothly and smoothly, and the excess will also be pressed on the masking paper.

7. Remove the masking paper. After the sewing agent is firm, carefully remove the masking paper, or with the help of a spatula.