How to play glass glue is the correct way to play?

When renovating a new home, we always need to use glass glue. Many people do not make glass glue in the wrong way, which is unsightly or troublesome to clean. Some families will also make their own glass glue. Next, I will introduce you to the use methods and skills of glass glue.

1.Remove moisture, grease, dust and other pollutants on the surface of the joint, clean the surface with solvents (such as xylene, butanone) when appropriate, and then wipe off all residues with a clean rag to make it fully clean and dry.

2.Cover the surface near the connector with plastic tape. To ensure that the working lines of the seal are perfect and neat.

3.Cut the nozzle of the hose, attach the needle-nosed tube, and cut it at a 45° angle according to the size of the caulking.

4.Install the glue applicator and keep the rubber material pressed out along the gap at a 45° angle to ensure that the rubber material is in close contact with the surface of the substrate. When the seam width is greater than 15 mm, it is necessary to apply the glue several times.

After gluing, trim the surface with a knife, remove the excess rubber, and then tear off the tape, if there is a stain, you can use a damp cloth to remove it.

5.The surface of the sealant cures after 10 minutes at room temperature, and it takes 24 hours or more for the sealant to be completely cured, depending on the thickness of the glue applied and the temperature and humidity of the environment.

Here's how:1. The glass glue mouth should be cut with a utility knife, because if it is cut with scissors, the glue will be uneven.

2. If you don't have gluing experience, you should pay attention to pasting the masking paper in advance, so that the glue will be straighter.

3. During construction, we must pay attention to the construction site, push the glass glue gun at a uniform speed, and clean the glass glue near the glue mouth after beating the glass glue.

The glass glue method is preferred1. Look**: Many guests will put ** in the first place when choosing glass glue, after all, **low, the cost is low, and the quality will not be good**, so you must not be greedy for cheap, of course, **high is not necessarily good, quality first.

2. Look at the performance: when home decoration, glass glue needs to be used in many places, and the buyer should determine according to the actual use, such as doors and windows, around the toilet, acid glass glue should be selected, and mirrors or other items should be selected neutral glass glue, which can not be mixed.

Playing glass glue is a technical job, generally inexperienced people do not know how to do it, playing glass glue skills, the key is that the glass glue spit nozzle must be cut, into a certain oblique angle, the caliber is not too large, can just press the gap is good, after the glue, use plastic to cover the fingers. (The glue is not easy to clean on the hand) the uneven glue can be smoothed, be careful not to repeat the smoothing, it is best to do it at one time.

Renovation is a complex process that not only covers a lot of items, but also a lot of details. Playing glass glue during decoration is also a technical job, although it is a small detail, but it is also a technical work. The following is the method of playing glass glue shared by the master, which is very practical.

The first thing to note is that glass glue must be bought in a regular brand store, so that it will not become moldy in the future.

Here's how to make glass glue::

1. The first step is to use a lighter to bake the nozzle of the glass glue soft and make it flat.

2. The correct method is to cut the nozzle at an angle of 45 degrees, and then align it with the position of the glass glue.

3. According to the above method, put the glass glue flat into the glue gun, press the switch, and push it up from the bottom in turn.

4. When hitting glass glue, it must be molded at one time, and there can be no pause in the middle.

The above method can not only increase the glue discharge area, but also reduce the amount of glue. When playing glass glue, the emphasis is on one go, and there is also scraping while playing, so as to avoid the problem that the glass glue cannot be connected.

The following summarizes the method of playing glass glue, and I hope it can be applied in the decoration in the future.

The first is to hit the position of glass glue, which must be cleaned first;

secondly, it is the position of the glue, as well as the angle of the glue mouth;

Finally, when playing glass glue, speed is a very important factor, and you can't stop in the middle. When the large glass glue is used, it should be noted that the strength of the glue and the speed of the dragging gun should be matched well, which is very important.

It is better to play two centimeters wide.

How to make the glass evenly glued?

If you want to smooth the glue by hand, then you don't know what gluing is.

1. The most important thing is to hold the trigger of the glass glue gun with the right hand, and the force of extruding the glass glue must be even. It is necessary to use what we usually call resistance, that is, to maintain a certain amount of strength. But the strength can't be hit for a while and a little bit.

Because usually the glass glue is relatively large and spherical when it is just squeezed out of the nozzle, if the piece is large and small, it can only be smoothed by the method of smearing.

2 The left hand controls the glass glue gun nozzle. Be sure to keep the mouth-grabbing collar close to the gap and not swaying back and forth.

3. Keep your feet steady, pre-calibrate the distance you move, don't move your feet too much as much as possible, and spread your legs apart a little bit. In this way, you can ensure that you can use the upper body to translate or turn the waist and work hard to squeeze out the straight line of the glass glue. If you walk too much.

It will affect the stability of the extruded glass glue.

4. Adjust your breathing, don't exhale and breathe in too much, keep breathing in small increments, or even hold your breath for a short time, so that your upper body doesn't shake too much because of your breathing.

How to use glass glue.

1.Press the switch on the back of the glue gun with one hand and pull out the bolt with the other hand;

2.Use scissors to cut the glue outlet at the top of the glass glue; Don't cut the threads when cutting;

3.Screw the glass nozzle onto the cut glue outlet;

4.Put the glass glue with the glue nozzle screwed flat into the glue gun;

5.Press the switch on the back of the glue gun, push the bolt forward, and fix the glass hose;

6.Align the nozzle with the position where the glass glue needs to be beaten;

7.Pull the trigger of the glue gun firmly to inject the glue to the desired position;

8.Finally, use a scraper to scrape the beaten glass glue flat and modify it evenly;

9.After the glass glue is beaten, it generally takes 1 hour for the surface to be polished; 24 hours to dry; During this period, it is best to use other methods to secure the relevant object and not shake it;

The correct way to use glass glue.

There are also some things to pay attention to when using glass glue, otherwise it will affect the service life of glass glue. The life of ordinary glass glue is about 5 years, even if it is high-grade glass glue, its life is only seven or eight years, so when it reaches a certain age, you should pay attention to whether the glass glue at home should be replaced; Glue should be operated by professionals to avoid uneven and uneven beating; When gluing, the attached surface should be free of oil, dirt and water; Do not use the glued utensils within 24 hours after gluing. The shelf life of glass glue is between one year and one and a half years, and the glass glue that has passed the shelf life will be unusable due to curing, and the shelf life of the glass glue after opening will be shortened accordingly, and the curing degree of glass glue should be carefully checked before use.

The glass glue is particularly ugly if you make a mistake, and today I will teach you how to make the glass glue.

Hello, the glass called requires the technique quickly. Find the right place to glue.

Methodological steps.

1 Use a lighter to bake the nozzle of the glass glue until soft, and then pinch the nozzle of the glass glue.

2. Nozzles for glass glue, with a small bevel angle of 45 degrees; Align the nozzle with the position where the glass glue needs to be beaten;

3. Put the glass glue with the glue nozzle screwed flat into the glue gun; Press the switch on the back of the glue gun, push the bolt forward, and fix the glass hose;

4. Pull the trigger of the glue gun firmly to inject the glue to the desired position;

Tips: By making this glass glue nozzle, you can increase the glue area and reduce the amount of glue.

When playing glass glue, scrape while beating, while saving glass glue, there will be no problem that glass glue cannot be connected.

Recently, I tossed at home, and I saw that the glass glue played by the decoration master was very beautiful, and I couldn't play like that, because I pasted a mirror on the tile, and I figured it out for everyone's reference 1, and the size of the oblique incision was consistent with the expected size of the glue surface.

2. Uniform speed and force movement and glue pressing.

3. Wipe it with a plastic membership card, and then use a utility knife to remove the excess after the glue is dry.

It's all stupid, haha.

Preparation tools: glass glue (with glass nozzle), glue gun, scraper The first step, the technique of hitting glass glue is to press the switch at the rear with one hand, and pull out the bolt with one hand, as shown in the figure below

The second step is to cut the glue outlet on the top of the glass glue with scissors, as shown in the following figure

The third step, the glass nozzle is screwed onto the glue outlet, as shown in the figure below

Step 4: Press the switch behind the glue gun, push the bolt forward, and fix the glass hose, as shown in the figure below

The fifth step is to pull the trigger of the glue gun and inject the glue to the desired position, as shown in the figure below

Sixth, the last scraper can be used to scrape the beaten glass glue flat, as shown in the following figure:

When decorating doors and windows at home, in order to increase stability and sealing, glass glue is generally needed. How to fight the glass glue? PChouse will take you to find out.

1. For the parts that need to be made of glass glue, they must be cleaned in advance. In order to avoid the problem of glass glue opening or glass glue falling off in the later stage. It mainly cleans the dust and oil on the surface of the crevices to ensure that the glass glue can be bonded to the surface layer.

Second, for some relatively small gaps, you can take two glues. For the first time, apply the glue to the surface of the gap and gently press it into the gap with your hand. And apply this layer of glass glue flat, and then add a wide layer of glass glue on top of the glass glue.

Third, if it is difficult to control the width and narrowness of glass glue, I personally recommend that you paste masking paper on both sides of the gap in advance. Then glue the inside of the masking paper. This can control the effect of the glass glue after it is finished to a certain extent.