Washing machine spin motor not turning? The washing machine spins and the motor does not spin

The reasons and elimination methods for the double-cylinder washing machine to spin the dry barrel are as follows:

1. Shake the bucket with your hand before using it to see if it rotates flexibly.

2. Check whether the power supply circuit is normal.

3. After the timer is energized, the buzz is not turning, check whether the starting capacitor is not connected, or whether the starting coil is broken, the lead is off, or the starting coil is burned (the motor of the spinning bucket is most likely to burn, and if the spinning bucket leaks, it will burn undoubtedly).

4. After the timer is screwed, there is no movement, check whether the safety switch of the door cover of the dry barrel is broken, and whether the fuse is broken.

5. Use a multimeter to measure whether the motor winding coil is in good condition. The circuit diagram is as follows:

On the left is the circuit diagram of the washing motor, and on the left is the circuit diagram of the drying bucket.

The reason why the dehydration motor of the double-cylinder washing machine does not rotate is usually caused by the damage of the door switch of the dehydration barrel or poor contact, which can be solved after replacing or overhauling the door switch.

Determine the fault site first: 1) Close and dry the lid and do not hear any sound, which means that the lid is not in contact with the lid; 2) Close the lid of the dry barrel and hear the [humming] sound of the motor, but the motor does not rotate, this is the starting capacitor of the motor is broken, and the fault can be eliminated by replacing it with a capacitor of the same specification.

Washing machine spin motor not turning? 1. Check whether the brake on the motor of the dry bucket is not loosened, you can open the back cover of the washing machine to run the washing machine to see if there is any action in the brake, if there is no response, you can check whether the cable connected with the door cover is too loose or disconnected, adjust or connect the cable, and let the brake be loose when the door cover is opened.

2. Check whether there is water leakage in the washing machine bucket, if there is a leakage problem, the sealing ring can be replaced, it is recommended to install a waterproof cover on the motor to prevent water leakage from flowing into the motor and damaging the motor.

3. If the safety switch of the door cover of the washing machine is not in good contact or there is a phenomenon of rat biting off the wire, there will also be the phenomenon that the automatic washing machine is dehydrated and does not turn, it is recommended to disassemble the upper three screws of the washing machine and open the operation panel cover to check, and turn on the power supply after shorting the two wires of the door cover switch.

4. Check whether the belt at the bottom of the dehydration bucket is loose, and if so, tie the belt tightly, or replace the belt again.

1. First of all, check whether the adjusting rod nut on the drain valve is loose, which causes the tractor to be unable to pull the drain valve core apart and cause non-drainage, and fix the nut at this time to make it open the drain valve core. Some models should check whether the tractor cable is loose from the drain valve.

2. No dehydration caused by no drainage, it may be that the drain valve coil is burned out, the brake is not loosened, and the motor is too loaded to cause it to be unable to start.

3. If the nut is not loosened or the cable is not loosened, the retractor may be damaged and the drain valve core cannot be opened, and the retractor should be replaced at this time.

1. The washing machine should be read carefully before use. When in use, the washing machine should be placed on a flat and solid ground, and the distance from the wall and other items must be kept at least 5 cm.

2. The washing should be classified and washed in batches according to the material, color and degree of dirt.

3. Before laundry, remove the debris in the pocket to prevent hard objects such as nails, coins, and cards from entering the laundry bucket; Clothes with sediment should be removed from the sediment before putting them in the laundry bucket; Wool should be washed in a yarn bag.

I do appliance repairs. Judging from what you said, if you remove the belt, it can be rotated.1 After removing the belt, turn the spinning bucket by hand to try the rotational resistance, if it is difficult to turn, it means that the shaft of the spinning bucket is blocked by something.

Take the bucket out and clean it up and add some oil to the bearings.

2. If the dehydration bucket rotates very smoothly, it means that the dehydration motor is broken or the starting capacitor is broken, 3. Replace the starting capacitor first with the test machine.

4. It's OK to replace the motor yet

1.The power supply is not plugged in and is in a leakage situation: see if the power leakage switch has tripped.

2.There is too much clothing on the bucket to exceed its load and it will not work properly: just remove the excess clothes.

3.Parts of the barrel motor are damaged: replace the damaged parts in time.

4.If the belt at the bottom of the bucket is loose: tie the belt tightly or replace it with a new one.

I went to buy a washing machine and the dewatering shock could not turn up, because the capacitor inside was broken, the capacitor could be replaced.

Open the back cover, turn the spindle of the dehydration bucket by hand, if it rotates easily, the capacitor is broken, just replace it with a new one; If the turner sinks, the water seal is worn out, and it is enough to replace it with a new water seal. Generally** is 10-15 yuan.

If the capacitor is damaged, it will only 'buzz' and will not start

The biggest possibility is a short circuit between the motor coils, don't rewind the coils, which are not durable at all, and it is both laborious and costly; It is recommended that you replace the motor and go to the electrical components market to buy it for about 50 yuan, and if you take more than that, you can get it for 40 yuan.

1. Replace the starting capacitor with leakage or capacitance drop.

2. The coil of the dehydration motor is short-circuited between turns, rewound or replaced.

Go to repair the home appliance to repair it, and the inexpensive thing is the motor or belt. Let the professionals figure it out. Why didn't I buy a little swan at that time, my family has been used for ten years.

My washing machine can be washed without dehydration after washing.

You say the motor is bad, so how can it be washed?

..The clutch is broken.

Throw it in the trash. Or sell it to a scrap collector... I heard about trade-in. You go and get a new one. It's not interesting to repair.

It doesn't start, it buzzes, and it's obvious that the start is malfunctioning. There are two main reasons: 1. Failure of the starting capacitor; Capacitors need to be replaced.

2. The starting coil of the motor is burned. The motor must be replaced. Possible reasons are:

1. The washing machine does not rotate the bucket, and the first reflection is whether the power supply is plugged in and in the energized state. Whether the power leakage switch has tripped. 2. Whether there are clothes or other items on the edge around the washing machine drying bucket, causing the internal jam and not working normally.

3. The starting capacitor of the motor at the bottom of the washing machine is damaged, and the motor starting capacitor of the drying barrel may be broken. 4. The bottom belt of the dehydration bucket is loose, and it will not rotate and work. It is recommended to send it for repair.

There are many reasons for this, the main ones are the following:

First, the brake was not released.

The second is that the motor capacitor is damaged.

Third, the motor bearing is seriously worn or the lubricating oil is dry.

Fourth, there is an inter-turn short-circuit fault in the motor coil.

There are several reasons that can be checked one by one, first, the capacitor capacity is reduced, second, the motor is swept, third, the lack of oil, the fourth leather bowl and the shaft are corroded, the four throwing clothes are accidentally entangled in the shaft of the dry barrel, the fifth brake is accidentally held, the sixth timer fails, and the seventh motor winding is damaged. Through these tests, the cause will be investigated.

It could be a timer issue, a door cover switch not touching, a brake brake locking, a foreign object wrapped around the spindle of the dehydration cylinder, the dehydration motor itself, or a problem with the starting capacitor.

It must be that one of the instruments inside is broken. You can ask the master to take it apart and check it, and it is better not to wash it.

If the washing machine does not rotate when washing the drum or drum, but only rotates when dehydrating, in the case of the correct selection of the program, it may be an error in the relevant program, in this case, it is best to ask the manufacturer's after-sales service personnel to come to check and repair!

What is the reason why the washing machine motor does not turn and dehydrate normally.

Summary. Motor failure.

What is the reason why the washing machine does not turn but can be dehydrated?

Motor failure.

The reasons why it can be dehydrated but not rotate are as follows: 1. It may be a motor failure. 2. The solenoid valve is damaged. 3. The motor plug is loose. 4. The computer control board is faulty.

Washing machine is an indispensable electrical appliance in our home, we all know that washing machine has many benefits, in addition to helping us to clean the clothes, it can also be dehydrated and dried, and we do not need to do laborious things, so this is also the first element that many people should consider when buying a washing machine. Although we all know that the washing machine can clean the clothes, the washing machine is also prone to failure, such as what is the reason why the motor does not rotate when the washing machine is dehydrated? Next, let's analyze it for you.

Reason 1:

It may be because of the difficulty of starting the inter-turn short circuit of the dehydrated motor coil, resulting in the phenomenon that only the sound does not rotate, and the motor coil inter-turn short circuit fault needs to be re-embedded or directly replaced.

CausesTwo:

It may be that the masking is difficult to start caused by the reduction of the starting capacitor capacity, and the capacitor capacity can be detected and replaced directly according to the original model;

CausesThree:

The transmission belt is broken and the motor is buzzing but the wave wheel is not running, which may be because the clutch is damaged or the bearing beads in the dehydration motor are damaged and the image is stuck.

CausesFour:

It may be because the rotor in the motor cannot be started normally due to serious sweeping, if the motor has a serious sweeping situation, you need to ask the lathe to make a subtle correction of the rotor or directly replace the motor.