My house is plastered with wall tiles, but the joints are uneven, do you want to knock them all off?

If the wall tiles are still in the process of being paved, only after the paving is completed, it will be found that the joints are uneven. At this time, it is proposed that all the wall tiles that are paved will be taken down, and then all the adhesive raw materials on the reverse side of the wall tiles will be cleaned up.

The wall tiles have already been paved, and all the raw materials for the pasting have long been dried up. In that way, at this time, the wall tiles are difficult to ensure that they are easily taken down and re-paved, if you want to take them down, you have to knock them all off, and then the floor tiles are paved again, which will be very laborious and will burn money, so it is generally not easy to do this casually. To decorate the kitchen, the main push is to paste the tiles and floor tiles, because the floor tiles are fashionable and trendy, and they are very easy to manage in daily life, and the characteristics of moisture-proof, anti-fouling and oil-proof are of high quality, and they are indispensable raw materials for decorating the kitchen.

The specifications, tones, and textures of the floor tiles are not the same, and there are standard requirements for the construction of the project, and there are no tiles pasted in accordance with the specifications. The kitchen smoke exhaust is relatively large, the water demand is also large, it is inevitable to sprinkle on the ground, the floor tile seam should be made of tile seams, after all, the tile seams are concave points, the surface is not very smooth, after a long time, it will hang ash, the tile seams will be black, and it is inconvenient to remove it.

There are also some people who say, there is no seam heat rise and shrink in the middle and late stage of the floor tiles will be warped, this should be nonsense, this depends on the skills of the tiling master, if the paste is good, there will be no warping at all, the skills are poor, then it is a problem, tiles must find a highly skilled master. But if there is no seam, the technical standard of the brick-laying master is relatively high, and the fault tolerance is a little larger, and the shopIt will not be obvious whether it will be leveled or not. If there is no seam, the fault tolerance is relatively low, and the problem of uneven paving is very big.

I don't think it needs to be knocked out, if the newly renovated house is knocked out, it will cause a lot of waste of resources, and there will be a lot of dust, and the room will not be inhabitable for a few days.

I think it is necessary to remove all of them, because the thermal expansion and contraction of the tiles are affected, and it is very likely that there will be some problems.

It depends. If this situation is detected earlier, then even if the wall tiles are knocked out, the loss should not be large.

If you do not leave a joint, because of the thermal expansion and contraction characteristics of the material, the wall and floor tiles will arch and fall off, and the same way when laying the floor, you should also leave 5mm joints around the wall. The principle of hot expansion and cold contraction is ubiquitous. It is suitable for building bridges and tiles.

The deliberately left seam is what we are used to calling expansion joints. If you don't leave that expansion joint, you'll regret it. The direct consequence of sticking tiles without leaving expansion joints is that the tiles will leave the ground and wall on their own, and we generally call this situation the tiles bulging up on their own.

Therefore, leaving expansion joints is also a summary of the wisdom of the ancients' practice.

The half-tiles soaked in water generally need to reserve a natural gap of about one millimeter, because the tiles have a shrinkage rate, and they will be more or less affected by the factors of thermal expansion and cold contraction after sticking to the wall, if there is not enough shrinkage joint, the tile will receive the extrusion of the surrounding tiles, and the porcelain tile paving must leave a seam, no matter what specification and grade of the tile, there will always be a certain difference in length, width, height and thickness, if you do not leave a seam, the effect of sticking out may be crooked. There are some necessary problems, so it is necessary to leave a seam. It turns out that they are all pasted without leaving gaps!

The current craft should be kept, and it should be sewn beautifully! Scraping sewing agent, good-looking!

To put it simply, in physics, all objects will have the phenomenon of thermal expansion and cold contraction. No matter which season you are pasting the floor, heating at home in winter, especially floor heating, the temperature of the floor tiles will rise, and then it will expand, if you do not leave a gap when you paste the tiles, it will make the floor tiles hard, and the floor tiles will be separated from the ground. Second, after leaving the joint, the caulk will be more beautiful and good-looking, or the poor quality of the cleaning floor tiles will be broken.

Leaving a seam is to reserve space for thermal expansion and contraction, and it is easy to bulge up if there is no seam.

The function of tiling joints is to prevent the tiles from cracking, deforming and falling off due to thermal expansion and contraction. If the gap is too small. That is, it will cause cracking, deformation, and falling off.

The reason for the seam is because the tile has the principle of thermal expansion and contraction, if the gap is left small, it may cause the tile to crack, bulge, tile size and construction will have more or less size errors, if the seam is too small, it may cause the tile joints to be uneven and unsightly.

The reason for the tiling is to prevent the principle of thermal expansion and cold contraction, which affects the overall ceramic tile. If the gap is too small, it is easy to cause the adjacent tiles to crack, causing unnecessary losses.

Because no matter what the material will have the effect of thermal expansion and cold contraction, if there is no gap when pasting tiles, the bricks will be squeezed into each other, and the gap left is too small, which will lead to cracking or hollowing of the tiles in the future.

When interior decoration, many community owners will be confused, and the floor tile paving has not advocated seamless splicing paving? Why do interior decoration masters propose to leave joints for tiles?

One: Is it possible to pave tiles without leaving seams?

The answer is no. Tile paving must leave seams, no matter what specifications and models of floor tiles, there will always be a certain difference in size and thickness, if there is no seam, the effect of pasting on may be crooked. In addition, there is also the harm of heat expansion and cold contraction, even if the floor tile is not greatly affected, it still has to follow the laws of nature, therefore, it is necessary to leave joints.

Second, tile pavingWhy should there be a seam?

1. The characteristics of thermal expansion and cold contraction of floor tiles

In the case of heat or temperature changes, wall tiles and mixed mortar will have a certain telescopic type, if there is no seam, it will cause the floor tiles to bulge or crack in the process of later application.

2. Tile repair is more convenient

For example, due to human reasons, the hanging object accidentally falls and causes the floor tiles to be destroyed, and if the joints are left, it is very easy to replace the damaged floor tiles.

3. There is a deviation in the floor tiles

Although ceramic tiles are now all mechanized production, but in the process of commodity production, there will be a certain size error (the deviation is too large to attribute to the quality of the product), if there is no seam, it is easy to occur when the joints of the floor tile parquet are not leveled, which directly affects the beauty of the floor tiles.

4. Deviations in the construction process

The paving of floor tiles belongs to a construction project with a very high grasp of the situation, and the workers cannot completely ensure that there is no deviation in the case of paving a brick in the case of all paving. If there are no seams, it is difficult to ensure the verticality of the gaps in the floor tiles, which directly affects the appearance of the floor tiles!

5. Tile joints will look better

The regular wireframe produced by the tile seam paving can achieve a certain three-dimensional sensory effect. At the same time, its function can not only decorate the overall paving space, but also reduce visual fatigue in a sense.

Be sure to leave relevant gaps, of course, no, if you don't leave a gap, it will lead to water leakage, and it will also lead to thermal expansion and contraction.

Leave gaps. If you don't leave it, it will lead to thermal expansion and cold, and then it will also cause the tile to crack, and it will also lead to water leakage.

When dragging tiles, it is necessary to leave gaps, and it is not okay to leave gaps, and it does not look beautiful.

When sticking wall tiles, I find that the joints are not uniform enough, how to remedy it? For the decoration of wall tiles, the brick joints are generally required to be left evenly, so they are very beautiful. If it is because of the tiling or the tile itself, the gap of the wall tile is uneven, then how should we deal with this situation?

Sticking wall tiles, in fact, is to achieve two functions: the functional protection of the tile wall; The aesthetic effect of the decoration.

Therefore, the left seam of the wall tile does not fall off uniformly, depending on our individual requirements for tile laying. The so-called consideration from the function of ceramic tiles is the problem that we can solve by sticking tiles on the wall. Wall tile is a type of tile that can protect the wall from being soaked in water, and on the other hand, it keeps the wall clean and helps us clean the wall.

So, from this point of view, the personal opinion is that uneven seams don't need to be knocked off.

So from an aesthetic point of view, it is completed by our wall tile paving, which gives us a neat and uniform sensory effect. However, after the tile is unevenly separated, the tile paving is very messy. So it's not particularly good aesthetically.

Whether we need to play now depends on our personal requirements for beautiful angles. Because everyone's requirements are different, so the results are different. The impact of demolition here is that we actually want to remove all the tiles on the wall, so it will incur corresponding costs and time.

Therefore, we should do the corresponding processing according to the different ceramic tile paving conditions.

The treatment method is to remove all the tiles on the wall and re-apply them. Because there will be no additional costs now, these costs are carried out by the responsible unit and the decoration company. What we lose is time, and time can be claimed accordingly against the decoration company.

Because we paste tiles on the wall, we use pasting materials in accordance with the specified requirements, and there is no quality problem. The only drawback is that the gap size is inconsistent. However, in terms of function, it is necessary to fully realize the protective function of its tile.

If you find that the joints are not uniform enough when pasting wall tiles, then you can communicate with the master of tiling and ask him to re-paste them, or add some beauty seam agent to them as repairs.

In this case, you can fill it with a sewing agent, if the laying is very messy, and then it is very uncomfortable for OCD, you can remove all these tiles and then re-tile them according to the standard requirements.

You can buy some caulk, clean the gaps, fill the caulk into the gaps, wait until it solidifies, and wipe it with a rag.

In the case of interior decoration pasting tiles, there is no corresponding gap, which is related to the style of floor tile materialThere are some floor tile edges that do not have an inclination, 90 ° angle of the appearance, this kind of specifications and models of floor tiles, in the case of sticking on the wall, the edges are all aligned at both ends, without vacating the corresponding gap, like this situation, are tolerable, the floor tile style is different, according to the style of the floor tile, with different ways of pasting on the wall.

Or in some areas, the temperature difference is not very large, and it is normal to leave no gaps. There is no gap for pasting tiles, and the relativity of engineering construction is simple and convenient, so you don't have to worry about the difference in gap width. Generally speaking, the relativity of the beveled style of floor tiles is quite rare, in the case of purchasing floor tiles, because they are all non-professional, do not understand the edge of the floor tiles, in fact, the edge of the floor tiles is curved, but this confusion is very, very small, basically everyone can not see it with the eyes, and the tiling master mistakenly thinks that it is an oblique floor tile.

In the case of wall gluing, there is no corresponding gap. Floor tiles are also subject to the hazards of heat expansion and cold contraction. It is also said that the floor tiles that we stick on the wall may expand and converge to a certain extent due to the factors of the material itself after being subjected to temperature changes.

Because the relative density of our wall tiles needs to be lower than that of floor tiles. The basic wall tiles are all made of highly absorbent floor tiles. For example, the most common glazed brick.

Therefore, the relative expansion or shrinkage of this kind of floor tile after being exposed to cold or heat needs to be larger.

After the paving of the floor tiles on the wall is completed, there will be a situation of "heat expansion and cold contraction", and the floor tiles will be pressed against each other. Whether it is a floor tile or wall tile decoration design, the actual effect of leaving joints and paving will be better! Since the current caulking raw materials have long been updated to tile grout,Compared with the previous use of cement or grout to plug the joint, the actual effect is more beautiful and generous, and the sense of hierarchy is more hearty!

I think it will have an impact, because the tiles will expand and shrink under the influence of the weather, and if there are no seams, the walls may bulge when the weather is hot.

This depends on the style of your tile, if the corners of the tile are not curved, then it doesn't matter if there are no seams.

The impact is not very big, it's good that there are no brick joints, and there is no need to clean up the dust inside.

In the case of interior decoration sticking to wall tiles, there is no corresponding gap, which is related to the style of tile materialsThere are some tile corners and no arc, 90 ° angle of the appearance, this kind of specifications and models of tiles, in the case of sticking on the wall, the corners are all aligned at both ends, do not need to leave the corresponding gap, things like this, it is also allowed, the tile style is not the same, according to the tile style, with different ways to paste on the wall. Or in some areas, the temperature difference is not very large, and it is common to leave no gaps.

In the case of interior decoration sticking wall tiles, the corresponding gaps must be left in accordance with the provisions of the engineering construction specifications for sticking wall tiles. The advantage of sticking wall tiles without leaving a gap is that it is very rateful, without looking at the tile gap, the two ends can be aligned to build the project, but the tiles pasted on it have no actual effect, and there may be some quality problems. At that time, I thought it was very good, and it didn't take long for all kinds of problems to manifest themselves.

Therefore, there is no gap in the construction of the adhesive wall tiles, and there is a probability that the wall will fall down. In the case of sticking wall tiles in interior decoration, we must leave the corresponding gap, which is the deformation joint of the tile, leaving the advantage of the expansion joint, not only to better do the tile beauty joint, but more importantly, to prevent the hot expansion and cold contraction, the tile is squeezed by each other, and the bulge falls down. The tiling master did not leave the corresponding gap, which is a problem of adhesive product quality. Generally speaking, adhesive tiles must leave a corresponding gap, which is certainly needed.

Tiles are also subject to the hazards of heat expansion and cold contraction. It is also said that the tiles we stick on the wall, after being subjected to the change of temperature, are likely to expand and converge to a certain extent due to the factors of the material itself. Since people's wall tiles also need to have a lower relative density than pavement tiles.

The basic wall tiles are all highly absorbent tiles. For example, the most common glazed bricks. Therefore, the relative expansion or retraction of this kind of tile after being exposed to cold or heat needs to be larger.

Said to be seamless splicing paving, in fact, no matter how good the tile connection place will appear from beginning to end there will be a little gap, it is very likely to ensure the actual effect of seamless splicing, close up or touch can always feel that there is a gap, and then talk about "seamless splicing paving" I feel that there is a lack of ceramic tile decoration design of the kind of layering, but it does not look good! Therefore, I think that whether it is a floor tile or wall tile decoration design, the actual effect of leaving joints and paving will be better! Since today's raw materials have been updated to tile grout, the actual effect is more beautiful and generous than the previous cement or grout grout, and the sense of hierarchy is more hearty.