What are some practical ways not to remove the grille when cleaning the fan?

Prepare a watering can, pour baking soda and dish soap into it, dilute it with water, tighten the lid and shake it evenly. Next, spray the solution from the pot on the front and back of the fan, and spray more where there are many stains.

Power on the fan to run automatically, since baking soda and dish soap can clean stains, while the fan is running, the stains on it will be blown away with the blowing wind. After a while, the stain on it will be clean.

First, you can choose a relatively long and thin wooden stick, that is, the kind that can be stretched into the net pocket, tie a strip of cloth at the end, and clean it with a strip of cloth. Second, you can choose a hair dryer and use the wind power to get out the dust from the fan blades of the electric fan.

If the fan blades are not too dirty, you can use a hair dryer to blow off the dust on the fan blades, and if they are dirty, you can use a discarded toothbrush to clean them, the toothbrush is small and can be used to clean up the details.

Prepare a sponge and scratch it a few times, then dip the sponge in cleaning agent and wipe it directly, or you can use a cloth and put it in water with white vinegar and wipe it directly.

The common electric fan grille is actually very convenient to disassemble, because the general electric fan has two functions: the tap grille and the detachable chassis, which are divided into four steps:

1.First disassemble the fan head, open the front grille of the electric fan, and disassemble the fan blades and rear grille respectively;

2.Next, remove the riser of the electric fan, loosen the screws above the fan, and take out the entire upper body;

3.Finally, disassemble the fan disc, loosen the big screw at the bottom of the abutment, and then remove the tube on the abuttress to complete the disassembly;

More information: Cleaning, clean the disassembled fan head, riser and foot plate separately, and then install it according to the previous steps. This completes the cleaning of the fan grille.

Note: Rotate the shaft of the fan by hand, it feels very tight, indicating that the motor bearing is poorly lubricated, the motor should be disassembled, the shaft should be polished smooth with fine sandpaper, and then wiped clean, add lubricating oil, including the linoleum in the inner shell of the bearing, and the orange cavity should drip some lubricating oil, and then install it, tighten the fixing screws slowly, and slowly tighten the angle, it is best to use the screwdriver wooden handle to knock the shaft frequently, so as to ensure that the rotor of the sailshirt and the bearing are concentric, and ensure that after the screws are tightened, the shaft rotates flexibly and without resistance. If the low gear still can't be started, it means that the capacitor capacity has decreased, and the capacitor should be replaced with a new capacitor of the same capacity.

The electric fan needs to be cleaned, and the grille and blades are already full of dust, and we can use the following methods to disassemble and wash. We first unplug the power of the fan, then unscrew the screws of the plastic ring and remove the grille, and find a wet rag to wipe off the dust. We can clean it more carefully, and we have to remove all the blades and grilles for cleaning.

01 The fan will be very dirty after a winter, and if we want to clean the fan, we must first unplug the power. It is only safe when unplugging the power supply and cleaning the fan, we have to unscrew the screws on the plastic ring.

02 The next step is to remove the grille, as long as the screws are unscrewed, the grille can be removed. The grille will be full of dust, so we should be careful when removing the grille so as not to lose the screws on the grille.

03 We will find that there is a lot of dust on the grille, we can take a damp rag to wipe it. We can also get some dish soap to clean the dust off the grille, and wipe it off with a dry rag after cleaning.

04 We can also use a brush to dust off the dust, and it is best to take the fan outside for treatment, otherwise it will pollute the environment of the room. We can also use a vacuum cleaner to suck up the dust, and when the grille is cleaned, it can be reassembled.

** Below:1. First of all, break the chuck of the protective mesh in the clockwise direction, as shown in the following figure:

2. Remove the front mesh cover of the electric fan after loosening, as shown in the figure below

3. Then unscrew out the spindle screw cracker, as shown in the figure below

4. Then take out the fan blade, as shown in the figure below

5. After loosening, the net nut is manually screwed out, and the ruler is shown in the figure below

6. Finally, take out the rear net, as shown in the following figure

Replacing the grille of an electric fan can be done by following these steps:

1.Turn off the fan and unplug it to make sure the fan stops running completely to avoid accidents.

2.Observe the grille of an electric fan, which is usually attached to the fan's housing by screws. Locate all the screws holding the grille in place, noisily and loosen them using an appropriate screwdriver.

3.When you loosen the screws, be careful to keep the grille stable so that it doesn't fall or damage other parts on the fan.

4.After removing all the screws, gently remove the grille. Sometimes the grille may have some clips or other fastening methods, and if there is, a slight force can be used to gently pull the grille apart.

5.Take out the new grille and make sure it matches the housing of the electric fan. Align the fixing holes in the grille with the holes in the fan to make sure the grille is secure.

6.Tighten the screws on the grille step by step, making sure the grille is securely attached to the fan. Be careful not to tighten the screws too tightly to avoid damaging the grille or causing the fan to run abnormally.

7.Check the fastening of the grille to make sure it is securely mounted on the fan and is not loose.

8.Once the replacement is complete, plug it back in and turn on the electric fan to make sure it's functioning properly.

Please note that during the process of replacing the electric fan grille, ensure safe operation and avoid electric shock or other accidental injuries. If you are not confident in yourself or are experiencing difficulties, it is advisable to ask a professional to do a replacement.

** Below:1. First of all, break the chuck of the protective mesh in the clockwise direction, as shown in the following figure:

2. Remove the front mesh cover of the electric fan after loosening, as shown in the figure below

3. Then unscrew out the spindle screw cracker, as shown in the figure below

4. Then take out the fan blade, as shown in the figure below

5. After loosening, the net nut is manually screwed out, and the ruler is shown in the figure below

6. Finally, take out the rear net, as shown in the following figure